That's a seven year long bump.
Type: Posts; User: Sarich
That's a seven year long bump.
You wouldn't be able to get the scrolling effect on a CF 7.5. The sound card has to be made to support the scrolling effect, which is what the CF-LS is for.
Force Action? You mean the plastic sabers? You're probably not gonna be able to fix that.
That 125 isn't in dollars. It's in Euros.
Just use a white diode for the FoC. It'll give you the exact effect you want.
Why do you have swing and clash sensors in your cart? Those don't do anything on their own because they were used as replacement parts on MR boards, if I recall correctly.
One thing I would change...
If you are gonna use the long switch, you will need a switch bezel. Add one of those or swap over to a short switch with the converter.
I don't think the power supply in an Ultimate FX saber would be able to properly power a Makoto and I don't think the board could handle the power needed. That being said, I don't think anyone has...
Swap the latching switch out to a momentary. NBs can't use latching.
No problem.
Are you using the MWS switch? If you are, you just need to put a solid piece of wire connecting the two terminals. If you are using a standalone resistor, just bend a leg into each terminal.
You can get 45 degree and 90 degree angle sink tubes from any hardware store.
Yes, that is true, lemme pull it up:
https://scontent-b.xx.fbcdn.net/hphotos-prn2/v/t34.0-12/10299317_10152020503071695_501450026_n.jpg?oh=89caf92a2dfbb6cb63c85d66421ea18c&oe=536399E3
It's a 4...
I did think about that one, but I wanted to be able to have the bottom half of the saber slide off to gain access to the recharge port, and that holder prevents that.
So, once I get settled in to my new apartment in a few months, I'm finally going to be buying the parts I need to make my Crystal Focus 7 saber. However, I am super paranoid about chassis parts,...
I mean, it's possible to find a diffuser, you would just need to find something that will fit inside the blade, though most of the time when folks take that stuff apart, it's to upgrade it to...
Gungn1r is right. A momentary switch will not get the effect you desire, since you do have to hold the switch to keep the saber on. I know there is a workaround, but for the life of me I can't...
The sinktube blade holders don't actually fit inside the threaded tube you use for the handle of the saber, assuming it's the kind I am thinking of. I made a pop-up drain saber last year, and it...
If it is the kind of sink drain I am thinking of, you'll want this.http://www.thecustomsabershop.com/125-Sink-tube-LEDBlade-holder--P269.aspx
Pictures would be great though, just so I know I...
Thank you for the timely response SS. That is exactly what I thought.
Alright, so my question today is a very simple one. Is it at all possible to wire the R.I.C.E. and recharge port to be the same thing. As in, can you have it both access R.I.C.E. and charge the saber...
After seeing that, I know who precisely did the conversion of the saber. You might just be better off getting a new LED module. May cost a bit more, but you'll be able to get the proper green LED and...
The saber wasn't stock, it was converted somewhere down the line. I noticed in another thread Cern posted. (I posted there too.)
You're going to need to get a new heatsink and housing for the LED so it can actually stay in the saber. Her Obi Wan was not a stock MR, it was a conversion from somewhere and the blade holder for it...
My friend calls mine "Soldering Robot," possibly because I have it posed differently every time he comes over.