Likely the battery in your VV saber is improperly charged or when you messed up your sd card it affected the settings, as we have not found that at all. We have tested our sabers and blades against...
Type: Posts; User: Allaerra Secura
Likely the battery in your VV saber is improperly charged or when you messed up your sd card it affected the settings, as we have not found that at all. We have tested our sabers and blades against...
Once again, this is a totally uneducated point of view and I am wondering how the heck you arrived at this assumption:rolleyes:.
The only Sabersmith I know who might fit that description is...
No, this is not the math. The LEDs are wired in series, so they are sharing current adding voltage. So, they are using 1000 ma. The batteries are also wired in series, again sharing current adding...
Sorry, but every LED and every MR board is different. MANY P4 reds have blown on that very set up. Just because yours haven't and many others haven't does not mean that is always going to be the...
Might not be technically UV but they are dim and don't look purple:-|.
Overlays were 22 gauge brass sinktube overlays powder coated flat black:cool:.
Over all, we have gotten superior results with Seouls and LEDEngins than with rebels. Not saying they all "suck", just that we get better, brighter, and more consistant results with those other...
No the resistor can go on either side. It is probably a good idea to draw up your schematics to double check, just to be safe;). No need to post a separate thread. Just post it here and we can...
No, you really need to use heatshrink. It is available all over the place. You are going to have to do some searching;). We normally make two positives coming off the battery pack to simplify...
Yes, for example:
You want to determine which type screw you are using so you can get the size. Let's say you are going to use this...
Yes, you can, although Harbor Freight might be cheaper for the drill press. Some people just use a hand drill and tap when they first start out, but it is difficult to get a clean hole that way. ...
What are you trying to install a screw for? Normally, you would need a drill press and a tap of the appropriate size. However, if you do not have access to those and are buying parts from TCSS, you...
It is not really a limitation. What if you normally use a latching switch for your sounds, but want to have a revealable "crystal chamber" font and you have a momentary on the crystal chamber? This...
The pommel is removed by first removing the control box. There really should be no need to remove the pommel on this saber for any reason, however;).
That is a matter of personal preference. I would say about 90 percent of the time, the recharge port is exposed. We flush mount ours, but there is also a nut to secure it which may be easier for a...
Hilt in the same position as the drawing. That's a great idea. Not sure why we didn't think about it. We'll try to get that shot before it gets packed up to its new home:).
You are not going to be able to use this LED without the correct power. You are going to have to learn both how to make a battery pack or buy one already made and also how to install a recharge...
Clever:D
I really like these, this was such an innovative idea. It is something I never would have thought of. Great imagination to look at a shaver head and think, "hey that would make a good...
This is just absolutely incorrect. If you are going to post misinformation and then you are going to stubbornly maintain your position, that is unfortunate. You can find the information on these...
So, you are going to wire the LED directly to a battery or batteries that puts out 5A? Hmmm...seems ill advised. @Bianchi, use a driver;)
As far as the potentiometer, that is fine to measure the...
Congrats Harry! Sweeeeeeeeeet Don!:p
Another nice conversion LDM! Love the ramping effect!
That is very sweet! Nice machine work. Did you do the pommel yourself? I like it!!!
Nicely done, and well executed! Though, not to burst your bubble, our own Randy of Arm on Fire Designs already designed this part and proposed it as an MHS part a few months back and it may be...
Makoto blades are very impressive! However, if you want to do any real dueling, the LEDs will break leaving dark spots. Beautiful for an ornamental saber, not so hot for a saber that will see a lot...