Search:

Type: Posts; User: jdubzw

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    14
    Views
    32,858

    Just an update on this, I think it was actually...

    Just an update on this, I think it was actually the charger that was the problem.

    Once I got the recharge port put in, I plugged in the charger and it took a good 6 hours to fully charge the...
  2. Replies
    14
    Views
    32,858

    Thanks for the info Kevin. I'd say I'm...

    Thanks for the info Kevin.

    I'd say I'm probably using it about 30-45 minutes then it's going into deep sleep, and the last time it happened about 2 weeks later I went to fire it up and it never...
  3. Replies
    14
    Views
    32,858

    I'm using the 18650 Trust Fire batteries from...

    I'm using the 18650 Trust Fire batteries from TCSS. They're the single batteries that are in the 18650 battery holder from TCSS also.

    So now I'm really super curious about what is causing that. ...
  4. Replies
    2
    Views
    12,343

    Thanks for the confirmation! I'm using the...

    Thanks for the confirmation!

    I'm using the Trustfire 18650 individual batteries currently from the TCSS, and those are just in one of the 18650 holders found in the clips and connectors. That's...
  5. Replies
    2
    Views
    12,343

    Pico Crumble - Wiring Check

    Hey all, I'm looking to rewire my PicoCrumble with a recharge port as I'm tired of swapping batteries. From another post, I THINK I have the correct wiring. The Pico's are very different than any...
  6. Replies
    14
    Views
    32,858

    I'm not sure what causes it, but on my pico...

    I'm not sure what causes it, but on my pico sometimes it'll go into deep sleep, but it'll still drain the battery dry once in a while. If I recharge that same battery it's totally fine, but I have...
  7. Replies
    5
    Views
    2,586

    Thanks Tim I appreciate the quick response! The...

    Thanks Tim I appreciate the quick response! The best answer appears to be stick to the Trustfires :P
  8. Replies
    5
    Views
    2,586

    On the battery it says "discharging protection...

    On the battery it says "discharging protection circuit". Is that the same thing or are they just playing with semantics?

    This is a link to the same kind I've got - this one comes in a charging...
  9. Replies
    5
    Views
    2,586

    Battery question

    Hey everyone. I'm just curious about these 18650 batteries sold by the customer saber shop and other batteries like EBL brand 18650's. I had a set already of 3.7 3000mah batteries by EBL. The...
  10. Replies
    4
    Views
    3,562

    This is awesome man thanks. I had the hardest...

    This is awesome man thanks. I had the hardest time searching out if this was a thing, so hopefully this helps someone else that does the same kind of search :)

    That's good to know! My idea...
  11. Replies
    4
    Views
    3,562

    But with the NB, there's a separate pad that...

    But with the NB, there's a separate pad that utilized the FoC, correct? By not using it, isn't that feature just completely missing? I can see how it would work with the Pico Crumble since the FoC...
  12. Replies
    4
    Views
    3,562

    Single LED Flash on Clash?

    Hey all, I've been trying to research this and I'm having a heck of a time finding information. Is that because having a flash with a single LED is just not possible and you need to use a tri in...
  13. Replies
    34
    Views
    13,946

    Awesome thanks! When it comes to lining up...

    Awesome thanks!

    When it comes to lining up internal parts though, are you using a similar method, where two holes line up with each other? Or would you do it with say like a set screw instead...
  14. Replies
    34
    Views
    13,946

    I'm curious about this also - I just built my...

    I'm curious about this also - I just built my first saber, but after removing the battery a couple of times I'm really thinking I want to change it to a rechargable setup and change around my wiring...
  15. Replies
    7
    Views
    19,196

    Got it sorted! Upon inspection using a much...

    Got it sorted!

    Upon inspection using a much higher magnification, there was an extremely small solder ball that fell on the top of the amp (I think it was the amp at least). I could barely see it...
  16. Replies
    7
    Views
    19,196

    As in, it's in the battery holder piece and it's...

    As in, it's in the battery holder piece and it's not clipped in all the way? I'm currently using the 18650 housing that includes the speaker holder from TCSS and it's clipped in. Should I maybe...
  17. Replies
    7
    Views
    19,196

    Hey all - update... I got in touch with Zook, who...

    Hey all - update... I got in touch with Zook, who by the way is the man as many know.

    I first tried a whole new speaker... no dice there.

    I ended up re-wiring the speaker wires and the + and -...
  18. Replies
    7
    Views
    19,196

    MoTG doesn't seem to be the problem... at least...

    MoTG doesn't seem to be the problem... at least from what I can see. I think I'm activating it, but with no sound it's just not doing anything.

    I'll get a new speaker to see if that's the problem...
  19. Replies
    7
    Views
    19,196

    I've been reading around in the NB forums, and it...

    I've been reading around in the NB forums, and it seems to me that if the sound doesn't work, something fried one way or another. Is that a reasonable thing to assume here? Or is there anything I...
  20. Replies
    7
    Views
    19,196

    Pico Crumble - Finished Build But No Sound

    Hey everyone,

    Very first build. Finished it up today and got it all wired. Went with the Pico just for some basic quality of life things (a little less expensive and the ease of color changing)....
  21. Replies
    4
    Views
    2,955

    Ohhhhh that's interesting... so, based on the...

    Ohhhhh that's interesting... so, based on the wiring diagram, the resistor could either go on the negative wires to the board OR the positive wires headed to the battery? I guess at least I got more...
  22. Replies
    4
    Views
    2,955

    Awesome thanks so much! That was really my hope...

    Awesome thanks so much! That was really my hope - I was looking to twist all 3 of those together and connect it to a single wire that would then go to the board to make that part easier. I think...
  23. Replies
    4
    Views
    2,955

    Pico Crumble Wiring Question

    Hey all, I'm pretty new to wiring and I had a question about the wiring diagram that's in the manual for the Pico Crumble. Here is the link to the diagram from the store.

    Under the "General...
  24. Replies
    3
    Views
    2,900

    New Saber Main Body Advice

    Hey all, I'm looking at putting together my first saber, and I'm really partial to using 2 extension pieces for the main body instead of one singular body piece. My worry though is the fit.

    What...
  25. Replies
    4
    Views
    3,280

    I saw that they had colored the wires in the...

    I saw that they had colored the wires in the diagram, but nothing on the board that I could see indicating that each channel had a specific pad allocated to that color. I've seen other people's...
Results 1 to 25 of 31
Page 1 of 2 1 2