Ok this is what I needed to know, you guys are great thank you (:
Type: Posts; User: DarkMessiah
Ok this is what I needed to know, you guys are great thank you (:
Ok I found this diagram (link below) in the manual and it seems to be basically what i am trying to accomplish however, it still shows the two dice with only one resistor, and if I am not mistaken...
Ok thank you very much for the help (: and is the power extender wired correctly?
I Wanted the av switch to light up when the saber ignites, is the wiring correct in that case?
Ok I had seen that way of wiring it too, it was just that I had been told to watch this video...
On the schematic for the switch are u talking about the placement of the wires on the switch? Plus to plus Ect?
And as for the parralel wiring I was getting this wiring from the multi die led...
Ok so first a run down on the build I plan on using: Nano Biscotte V2, powered by a Li-Ion 18650 3.7V 3400mAh Rechargeable Battery, Switch Craft recharge port, this tri-rebel...
Thank you for the reponce, sorry for the Newby question!
I have been looking into wiring FoC into my upcoming saber build using a NB v2 with a PEx and a rebel tristar. My question is, is it possible to have the third led flash while the other two leds...
And no I don't know where he gets his LEDs though I will say he changes which LED he uses when ever he finds better/stronger LEDs
The v3 is Makotos current standard blade or "real duel saber" it has one string of LEDs in the blade as opposed to the v3 plus which has two or the v4 which has four strings. Makoto recommends the V3...
Thank you (:
If I did want it to light up with the blade though would the shared current affect resistor calculation?
I am thinking of using this wiring skematic in my saber http://forums.thecustomsabershop.com/attachment.php?attachmentid=10454&d=1411406136 the alterations being a tri rebel and adding FOC. The...
so then when using li-ion packs, would using an appropriate resistor essentially work just as well as a buckpuck?
Ok sorry wasn't trying to imply you didn't just making sure my own concepts are correct, thank you.
For Clarification a buck puck acts as a resistor with the added ability of regulating the current put out ie. 700ma or 1000ma. So When using the NB with resistors on the LEDs will I have blade...
Single lithium Ion Cell 18650, with a NB 2.0, a momentary switch, a white rebel tri-star LED two diodes running parallel a third running as a direct drive each having their own resistor, a speaker....
Ok so If I wanted to run the neutral white Rebel tri-star wired in series, with no FOC, with a NB sound card, I would then need a power extendor, a 1000MA buckpuck, a momentary switch and an...
Ok So any suggestion to getting this general setup to work? A certain power supply? Different sound card? Or is running all four together as one big led not going to work? Again any information is...
Ok that video was very helpful thank you. And yes I would like to add sound preferably the Nano Biscotte Sound Module V2, and a quad led luxeon rebel in nuetral white, and I dont plan on adding FOC
This is the ledhttp://www.luxeonstar.com/neutral-white-4100K-sinkpad-ii-23mm-round-quad-led-230lm
I was looking to make a white saber and I was just looking on the luxeon site I guess they have quad led's would that be terrible hard to wire myself?
So in your opinion a 10w tri cree will be as bright as a v3? Also any note on if the V3 plus is really much heavier than the v3?
Thank you by the way!
I currently own an in hilt LED saber, I fight entirely one handed I prefer fighting with the lighter thin walled blades as opposed to the thick walled but I can work fine with either. My question...