Search:

Would it be possible to run a Lux K2 directly off of a hasbro board (clashflash still intact)?

I ask because I need a white LED and the shop is out of Seoul P4's.



Also, any ideas how to...

I bypassed the notion of using the board to power the LED.

I decided to take ArmOnFire's fury saber wiring diagram and use it for the wiring. It would appear that not enough power is getting to...

I separated the negative leads coming off the boards. When touched to the negative lead coming from the LED, each one lights up the LED.....

Hmm....

Short on board maybe?

Ok, everything works just fine except the LED is on even when the switch is off.

I just need to know how to fix that and I am finally done!!! YAY!!! :D

And Jay, I have already seen that forum...

Ok, I checked one of the wiring bits and it had come apart (purple wire to clash sensor).

Holding the two ends together, the clash sensor works.

Problem is, light is still on....

Are you sure? I just ask because as I mentioned before, I screwed up the wiring so it was a bit of a pain to rewire the setup. If that is the problem, I have no issues with just chopping off the...

I was wrong. I screwed up the wiring.

It works but for one issue. The lights stays on and the clash sensor won't work.

Any suggestion?

I am using the inner assembly of the yoda in my custom saber. I have made it so it will fit perfectly and I was all ready to put it in when this started.

Mind you, up until I cut the LED strip...

I wired up a FX Yoda sound board. I haven't removed the board from the casing. I plan on using the battery pack and switch of the FX.

When I hold the batteries in place, the LED won't light, and...

I have read and searched on this forum, there just isn't much concerning the Yoda FX.

Now, what I am planning does involve taking the black casing inside the Yoda's hilt and sliding it into my MHS...

I am wondering if it would be feasible to take the innards of a (in this case Yoda) MR FX lightsaber, tube and all and insert it into a MHS hilt.

Then just adding a new switch and wiring the Lux...

Well, I actually think I might have gone through two fx boards....

The one I remember the most was the Joe Jedi (616) board.

I tried to solder around the board's switch and ended up breaking...

Of course my other options are to either wait until I have the money for the UltraSound 2.0 board have commission that to be installed, or wait until I have more money (around $300) and just...

Greetings all,

I have the possibility of getting a MR FX Yoda lightsaber for $55. The problem is, when I constructed my saber before, I went through both a Hasbro and MR FX Build-Your-Own...

Ahhh I just ordered another one.

Any tips to help salvage the one I have would be most appreciated.

It looks like the wire pulled out from inside. No surprise considering how much it got moved...

OK! Now that everything is working I just have two problems to address....


I have too much wiring in the hilt... gotta shorten some of them.

And;

I have to reconnect the two places that I...

YOU ARE MY HERO....:cool:




batteries were dead.....

I am in desperate need of some help as this is third time I have attempted to install a sound card into my saber.

This last attempt involved using an FX Construction Kit sound board. Before I...

Well the main reason I wanted to use the titanium drill cutter id do I could get a matched set through both sides at once.

What I might do is just drill straight through in two spots, then use...

Well the main reason I wanted to use the titanium drill cutter id do I could get a matched set through both sides at once.

What I might do is just drill straight through in two spots, then use...

Well the main reason I wanted to use the titanium drill cutter id do I could get a matched set through both sides at once.

What I might do is just drill straight through in two spots, then use...

Well the main reason I wanted to use the titanium drill cutter id do I could get a matched set through both sides at once.

What I might do is just drill straight through in two spots, then use...

Well the main reason I wanted to use the titanium drill cutter id do I could get a matched set through both sides at once.

What I might do is just drill straight through in two spots, then use...

Basically twist two wires together and solder them on to the switch. One wire to the buckpuck, one wire to the accent LED.


Thanks! Can't wait 'til it gets here! WOOOT!!!

Yeah I forgot to mention the LED negative to the battery negative.

I will be using this switch:

http://www.thecustomsabershop.com/SPST-Push-onoff-Mom-switch-with-black-button-P44.aspx

And it...