Search:

Type: Posts; User: Tom Tilmon

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    39
    Views
    2,017

    The only components you need heavy gauge wire...

    The only components you need heavy gauge wire (22) is for battery, RCP, Cutoffs, and any Neopixel feed (positive and negative). YOu can use smaller gauge wire 28 or 30 for your tactile switches,...
  2. Replies
    3
    Views
    182

    or put a piece of paper over the diodes to...

    or put a piece of paper over the diodes to diffuse the beams.
  3. Replies
    39
    Views
    2,017

    I highly suggest either a cheap neopixel...

    I highly suggest either a cheap neopixel controller (they're 5 bucks) or a used NBIV/Prism as a test rig for your strips. You can rig it up so your strips can plug into so you can test their...
  4. Replies
    10
    Views
    1,282

    Making MHS Sabers happen right now is very...

    Making MHS Sabers happen right now is very impressive Matt, can't wait to see what awesomeness you come up with.
  5. Replies
    5
    Views
    612

    Who built the blade? Have you tested it, to make...

    Who built the blade? Have you tested it, to make sure it works in other neopixel sabers? If not, check on the target to see if you have any shorts. Probe outer and middle ring against one another...
  6. Replies
    6
    Views
    762

    YOu can dremel down the covertec retention screw...

    YOu can dremel down the covertec retention screw inside the hilt so that its flush inside the hilt and doesn't catch your speaker holder.
  7. Ridire, I use TCS WOW speakers all the time. ...

    Ridire,

    I use TCS WOW speakers all the time. It should be fine in your Spkr4 holder, its the same relative size as the Veco Bass 28mm sold also at TCSS. Now, the sticky foam that comes on their...
  8. Replies
    3
    Views
    779

    I NEVER REUSE the chineseum wires that come on...

    I NEVER REUSE the chineseum wires that come on the neopixels. It is absolutely dreadful. 22ga feeds (+ and-) 26 ga for data. I have hot glued the connections on the strips and blade connector for...
  9. Replies
    7
    Views
    1,196

    Glad you found it.

    Glad you found it.
  10. Thread: DV6 help

    by Tom Tilmon
    Replies
    1
    Views
    765

    Simple. There are copper traces running through...

    Simple. There are copper traces running through both sides of your switch holes. Now remember, switches both share a common ground, but the switch legs themselves must be independent. To make the...
  11. Replies
    7
    Views
    1,196

    Are you using an appropriate battery? Need one...

    Are you using an appropriate battery? Need one with a 15A cutoff. I'd be suspicious of a short in the strips or how they are wired with the symptoms you are describing.
  12. Replies
    7
    Views
    1,196

    If the strips worked fine before you put them...

    If the strips worked fine before you put them back to back, check for shorts between the strips. When they are back to back, you can have many areas of reverse polarity, which is REALLY bad. If you...
  13. Well, what is outside diameter of your...

    Well, what is outside diameter of your controllers? Once you have that, or can modify it to fit MHS, then we can maybe help guide you about how you could use MHS parts to build your beatsaber...
  14. Replies
    3
    Views
    1,178

    Doh! I was looking in thick-walled section and...

    Doh! I was looking in thick-walled section and not in "neopixel" supplies. I guess you already have it. Maybe just list in in both places?

    Here is the one I want, will be ordering some! ...
  15. Replies
    3
    Views
    1,178

    Well, this one, but hollowed out like the ones...

    Well, this one, but hollowed out like the ones available for the 1" thin-walled blades: https://www.thecustomsabershop.com/1-Thick-walled-Trans-White-parabolic-mirrored-blade-tip-P1546.aspx
    ...
  16. Replies
    3
    Views
    1,178

    Neopixel Blade Durability Test take 2

    Can you duel with a neopixel lightsaber blade? Are they tough enough for events like The Saber Legion hosts? I know most say: NO. I say yes, and so do the tests I ran. This blade in this saber...
  17. Replies
    7
    Views
    1,809

    So much greatness in the Outer hilt and inner...

    So much greatness in the Outer hilt and inner core. I am always amazed with your work, absolutely awesome.

    Tom
  18. Replies
    3
    Views
    1,196

    Absolute Starkiller mastery SA2CC!!!! This saber...

    Absolute Starkiller mastery SA2CC!!!! This saber ROCKS. The maker should be very proud.

    Tom
  19. Yes, Korbanth/Parks/TCSS Crossguard 2.0

    Yes, Korbanth/Parks/TCSS Crossguard 2.0
  20. Without seeing a macro view of this photo, the...

    Without seeing a macro view of this photo, the soldering of your SMD resistors look pretty good. You may have burned a resistor or had a bad one. I have had a couple bad resistors that I couldn't...
  21. Oops, I missed the NBIV, yep, only activation...

    Oops, I missed the NBIV, yep, only activation switch on the NBIV. Good catch DC.
  22. Replies
    449
    Views
    258,371

    Sticky: I would like to request a parabolic tip (neopixel...

    I would like to request a parabolic tip (neopixel style) for thick walled 1" blades that has a larger gluing edge inside the blade than current thick-walled options.

    TOm
  23. 3 pin switch? Can you link it in TCSS store. ...

    3 pin switch? Can you link it in TCSS store. You need momentary switches for Aux and power, and you should have separate switches, 2 of them. Each switch, if not illuminated should have 2 poles. ...
  24. If I have multiple wires going to the same pad,...

    If I have multiple wires going to the same pad, typically I splice them together before the board, and run a pigtail from that joint to the board so Only a single wire goes to the board for common...
  25. Replies
    6
    Views
    1,707

    Fredrik has an IR sensor working in the Proffie...

    Fredrik has an IR sensor working in the Proffie OS that can sense an IR beam from a blaster, and trigger a clash.
    https://youtu.be/mTqKa9CKwYM

    I'm not sure if CFX can add capabilities like that...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4