Search:

Type: Posts; User: Blinding_Phoenix

Search: Search took 0.02 seconds.

  1. Replies
    32
    Views
    9,785

    Thanks FJK. I already tested my board and parts...

    Thanks FJK. I already tested my board and parts for shorts and don’t have any. So hopefully this battery will sort out my issues. I’ll be sure to post a pic of my hilt when it’s finished though!
  2. Replies
    32
    Views
    9,785

    18110 Will this battery work? It doesn’t say...

    18110

    Will this battery work? It doesn’t say if it’s 15A?
  3. Replies
    32
    Views
    9,785

    I was using a 7.4 volt 18650 battery from TCSS....

    I was using a 7.4 volt 18650 battery from TCSS. But once I realized that wouldn’t fit in my build the way I wanted I switched to the smaller single cell 18650. I also bought the chargers for them...
  4. Replies
    32
    Views
    9,785

    The most frustrating part is that I had it...

    The most frustrating part is that I had it working one night. The blade lit up, I could change the length and color. Then when I woke up the next day and turned it back on. It only lit up red and has...
  5. Replies
    32
    Views
    9,785

    I should also clarify the leds on the connector...

    I should also clarify the leds on the connector turn red as soon as I plug the battery in. They don’t stay lit when I plug in the charger. And they turn off whenever o hold the aux button to power...
  6. Replies
    32
    Views
    9,785

    it does not

    it does not
  7. Replies
    32
    Views
    9,785

    ONLY the leds on the connector are lighting up...

    ONLY the leds on the connector are lighting up red when powered on, the blade won't power on and the leds don't animate, they are just a static red
  8. Replies
    32
    Views
    9,785

    Yeah I double checked

    Yeah I double checked
  9. Replies
    32
    Views
    9,785

    //CF-X Configuration - FOR LEDSTRIPS debug=0...

    //CF-X Configuration - FOR LEDSTRIPS
    debug=0
    logport=0
    vol=50
    menuvol=50
    menugest=0
    trackgest=0
    fontgest=0
    beep=40
    muteb=0
  10. Replies
    32
    Views
    9,785

    The new battery showed up and I took a break from...

    The new battery showed up and I took a break from the electronics to cut out my crystal chamber. But even with the new battery the blade won’t light up, and the the neopixel connector still only...
  11. Replies
    32
    Views
    9,785

    Found out the LS6 board has a short. But I have a...

    Found out the LS6 board has a short. But I have a backup board. I’m assuming I killed the battery from charging it too long. Have another battery on the way. I’m probably going to take a break for a...
  12. Replies
    32
    Views
    9,785

    But when I plug it in the recharge port no longer...

    But when I plug it in the recharge port no longer kills power. I’m using the ls6 upgraded PCB
  13. Replies
    32
    Views
    9,785

    I forgot to mention it worked when i went to bed...

    I forgot to mention it worked when i went to bed last night, but not when i woke up, i had it plugged in because the battery was dead, possible i fried the battery?
  14. Replies
    32
    Views
    9,785

    yep i have 7F installed on my sd card, my issue...

    yep i have 7F installed on my sd card, my issue now is, i have it wired up for final assembly, and the NPXL conncter is only lighting up red, and it won't light up the blade :(
  15. Replies
    32
    Views
    9,785

    Just double checked and I can confirm I do not...

    Just double checked and I can confirm I do not have the PIXIES folder adjusting the ls2 pad configuration
  16. Replies
    32
    Views
    9,785

    The PIXIES folder should be right in Extras on...

    The PIXIES folder should be right in Extras on the card right? Because last time I looked to configure it, I couldn’t find the file
  17. Replies
    32
    Views
    9,785

    Would 24 gauge be a better wire to switch to for...

    Would 24 gauge be a better wire to switch to for power to the NPXL connector?
  18. Replies
    32
    Views
    9,785

    Thank you, I already have the parts, I have the...

    Thank you,
    I already have the parts, I have the data out pad from pixel one wired to the data in pad on pixel two, they're wired in to the ls2 pad, they don't light up (although neither is the...
  19. Replies
    32
    Views
    9,785

    first cfx build help

    I'm trying to build my first saber and want a blinking switch box, like on Luke's ROTJ saber, but don't know how to wire up the switch box and can't find any diagrams.

    Hoping someone here has done...
Results 1 to 19 of 19