Search:

Type: Posts; User: Forgetful Jedi Knight

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    36
    Views
    1,893

    22 gauge is fine.

    22 gauge is fine.
  2. Poll: Sounds like you have some type of switch issue...

    Sounds like you have some type of switch issue (not wired properly, misconfigured, etc).
  3. Poll: What kind of build is this one? Another Tri-Cree?

    What kind of build is this one? Another Tri-Cree?
  4. OK, I reopened it. Let me know if you have any...

    OK, I reopened it. Let me know if you have any issues/need any help.
  5. Which topic is locked? I can unlock it for you.

    Which topic is locked? I can unlock it for you.
  6. Replies
    36
    Views
    1,893

    Did you check to make sure the battery is fully...

    Did you check to make sure the battery is fully charged first?
  7. Replies
    20
    Views
    384

    Putting it where you had it, the holes will...

    Putting it where you had it, the holes will likely be blocked by the heatsink module, sooooo.....
  8. Replies
    20
    Views
    384

    If youíre trying to put speaker holes in the...

    If youíre trying to put speaker holes in the choke, you should put them towards the bottom, where the sound is actually coming from.
  9. Replies
    20
    Views
    384

    It would be weak, probably look bad and would...

    It would be weak, probably look bad and would probably fall off with contact
  10. Replies
    8
    Views
    672

    Sounds like a dead battery to me.

    Sounds like a dead battery to me.
  11. Replies
    20
    Views
    384

    I doubt youíll ever achieve something like that,...

    I doubt youíll ever achieve something like that, youíd have to have custom work done on a choke like that with predrilled holes for the rods, and even THEN, Iím not sure if it would work or look...
  12. Replies
    1
    Views
    118

    A very light green.

    A very light green.
  13. Poll: Make the following change: strippower=0000

    Make the following change: strippower=0000
  14. Replies
    36
    Views
    1,893

    You have to know what version of firmware you...

    You have to know what version of firmware you have on your card before you just go randomly adding parameters.
  15. Poll: Please post your main configuration file.

    Please post your main configuration file.
  16. Poll: You either have a faulty recharge port, charger...

    You either have a faulty recharge port, charger OR there is a wiring issue with your recharge port.
  17. Replies
    2
    Views
    218

    You could use it, itíll just take some work to...

    You could use it, itíll just take some work to get it to work the way you want it to IIRC.
  18. Replies
    6
    Views
    1,009

    The V2 can withstand combat, as long as you build...

    The V2 can withstand combat, as long as you build them properly. Also, you can get switch holes just about anywhere, just ask and be specific (additional charges apply).
  19. The stock boards can’t handle a Tri-Cree (it can...

    The stock boards can’t handle a Tri-Cree (it can support one of the three die) and no, I don’t believe you can add FoC to a simple board like that.
  20. Replies
    5
    Views
    1,089

    You have to make sure that the LEDSTRIP= number...

    You have to make sure that the LEDSTRIP= number is approximately how many pixels you have in your blade, not “0”.
  21. Replies
    36
    Views
    1,893

    The CFX is normally set to run with a 3.7V...

    The CFX is normally set to run with a 3.7V battery. If you used any of the 7.4V from the store, they donít put out anywhere near enough amperage to run 2 Neopixel strips.
  22. Rob and I discussed the CFX video before I even...

    Rob and I discussed the CFX video before I even did it. Since he didnít have the time to do it, and I did, you guys got me for that one.
  23. Scott is right. That stuff is more for the...

    Scott is right. That stuff is more for the Ultrasabers crowd than this one.
  24. Replies
    3
    Views
    543

    You can use 2-56 screws as long as theyíre long...

    You can use 2-56 screws as long as theyíre long enough to get a good grip into the PVC.
  25. Replies
    17
    Views
    3,264

    Please do not resurrect threads that are a DECADE...

    Please do not resurrect threads that are a DECADE OLD.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4