Search:

Type: Posts; User: RavenXp

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Definitely looks good, though I could suggest you...

    Definitely looks good, though I could suggest you could possibly run the crystal chamber pixels off the LS2 data pad on the bottom of the CFX so you can have independent control over those pixels...
  2. Replies
    4
    Views
    1,076

    correction, I said 3.7v

    correction, I said 3.7v
  3. Replies
    2
    Views
    840

    if you mean the outer metal shield of the port,...

    if you mean the outer metal shield of the port, then yeah, the pad and that shield are connected so it should be fine.
  4. Replies
    2
    Views
    1,358

    unfortunatly no, the switchcraft style connector...

    unfortunatly no, the switchcraft style connector is designed to cut power to the electronics when the charging port in inserted, this looks like it is using a 2 prong barrel connector to input 5v USB...
  5. Replies
    6
    Views
    1,573

    We have a lot of the documentation for the...

    We have a lot of the documentation for the proffie on the discord server, but to get you started here is where I recommend you get your basic proffie info from: http://pod.hubbe.net/

    You can also...
  6. yep, should be good to go.

    yep, should be good to go.
  7. That is what I use by default in commissions that...

    That is what I use by default in commissions that have the room for them. They are larger cells, 21mm diameter and 70mm long over 18mm diameter and 65mm long. But there is plenty of space inside...
  8. doubtful that will provide the correct current,...

    doubtful that will provide the correct current, cells from that long ago usually had 5-8A current cutoffs on the protection PCB. you can try it, but do not be surprised if the blade starts to light...
  9. It does look like you have what you need, aside...

    It does look like you have what you need, aside from the proffieboard (TCSS now carries the v3.9 board which does have some advantages, but it does cost more than the 2.2). As for resistors, the...
  10. you are missing this, it holds the blade side PCB...

    you are missing this, it holds the blade side PCB in the blade: https://www.thecustomsabershop.com/1-Thick-Walled-Pixel-Blade-Adapter-P1347.aspx

    Also make sure you have the appropriate wire...
  11. Replies
    2
    Views
    1,213

    Polarity is so you can reverse the polarity of...

    Polarity is so you can reverse the polarity of the pad from how it normally would. This way you can use the pads with either a common anode RGB LED or common cathode version. As for your example, b...
  12. Replies
    5
    Views
    2,717

    I think it's less do do with the amp load the...

    I think it's less do do with the amp load the strip is capable of handling and more to do with the heat generation, I think I remember someone mentioning you could generate enough heat to melt the...
  13. Replies
    7
    Views
    2,602

    Etsy is always an option for the fancier blade...

    Etsy is always an option for the fancier blade plugs, but you can easily make your own or even convert an in-hilt one with something like this:...
  14. Replies
    9
    Views
    4,525

    I have to agree, it looks pretty bad compared to...

    I have to agree, it looks pretty bad compared to the other tech we have access to currently. It also would likely be much more expensive for the blade material that it would be for a standard PC...
  15. Hmm... all I could find was one super cheap one...

    Hmm... all I could find was one super cheap one on aliexpress, but I wouldn't go for it. The install itself is probably sub-par at best, dangerous at worse. Not many are currently making the crowd...
  16. Well, TCSS blades start at $115. ...

    Well, TCSS blades start at $115.

    https://www.thecustomsabershop.com/WS2812B-1-OD-Pixel-Show-blade-Ready-to-ship-P1711.aspx
    ...
  17. Yeah, as FJK stated, it's a physical change of...

    Yeah, as FJK stated, it's a physical change of the phosphor composition to get the color temperature. not something that can be altered with coding.
  18. Thread: Battery bulge?

    by RavenXp
    Replies
    2
    Views
    1,253

    Hmmm... that looks to me like the cell is...

    Hmmm... that looks to me like the cell is deforming and pushing the protection PCB out. You said this cell was from 2015? How was it stored? Was it stored at half charge, fully charged, or...
  19. Replies
    9
    Views
    1,740

    I already said why, density. normal pixel blades...

    I already said why, density. normal pixel blades (non KR stick) use pixel strips that come in a 144LED per meter pixel density. Most the time I see single color strips, they are far less, usually...
  20. Replies
    9
    Views
    1,740

    I've also never seen single color 5050 or even...

    I've also never seen single color 5050 or even 3535 footprint LEDs come in the correct density for saber blades. At least not on a strip.
  21. Replies
    5
    Views
    1,351

    Well, tbf a lot of them are the same, just with...

    Well, tbf a lot of them are the same, just with minor differences.
  22. Replies
    5
    Views
    1,351

    I think you meant an 07 since that's what was in...

    I think you meant an 07 since that's what was in the vid, still though pretty fine work. And I'm right there with you on people going for an empty from a place like korbanth rather than converting a...
  23. Replies
    1
    Views
    894

    Dingleflop (the dev that maintains the builder)...

    Dingleflop (the dev that maintains the builder) pulled them to work on them, then that got sidelined because he broke his arm, so till that heals they kinda are not in the live builder at the moment....
  24. Replies
    5
    Views
    1,351

    MR 2005 Vader CFX Conversion

    I actually forgot to post this here back when I completed it, but this is a MR Vader 2005 I converted from the original electronics (it was already converted from stock to in-hilt) to a CFX Pixel...
  25. Nice, it's good work. I personally did a...

    Nice, it's good work. I personally did a conversion of a '05 MR Vader to CFX Pixel a while ago for a client, pretty happy with how it turned out.
Results 1 to 25 of 276
Page 1 of 12 1 2 3 4