Search:

Type: Posts; User: Firestorm1964

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    1,328

    So beautiful. I need to get on the forums more...

    So beautiful. I need to get on the forums more often.
  2. Replies
    3
    Views
    572

    Gotta love those Jevaho Bone Shrouds.

    Gotta love those Jevaho Bone Shrouds.
  3. Replies
    36
    Views
    6,400

    So the mylar that you use is adhesive-backed? I...

    So the mylar that you use is adhesive-backed?
    I suppose this is something that would have to be bought wholesale, since mylar is so cheap...
    I think I've found something that would work, but would...
  4. Replies
    13
    Views
    2,467

    *bows awkwardly* I'm sure I'm not the first

    *bows awkwardly* I'm sure I'm not the first
  5. Replies
    13
    Views
    2,467

    Long time no see! After 20 or 30 tests and...

    Long time no see!

    After 20 or 30 tests and countless hours of research(including my high school chemistry teacher) I've made these conclusions;

    Aluminum Oxide is our culprit here. Apparently,...
  6. Replies
    13
    Views
    2,467

    I've read/watched several tutorials using various...

    I've read/watched several tutorials using various solutions, such as muriatic acid(used to balance pH in pools), or RootKill, both of which are available at my place of work(Home Depot). Once I'm...
  7. Replies
    13
    Views
    2,467

    Right. I have read a little bit about it. I'd...

    Right. I have read a little bit about it. I'd just want to plate copper, I think. As you said about copper, then nickel(or nickel, copper, nickel depending on tuts), I've seen much the same...
  8. Replies
    13
    Views
    2,467

    ElectroPLATING rather than etching

    Has anyone ever tried electroplating rather than etching? Or even, etching a design then using the same stencil to plate a different material in it?
    Seems doable, but I must admit I've never seen...
  9. Replies
    3
    Views
    1,035

    This is just a concept build, I wanted to make...

    This is just a concept build, I wanted to make sure I could do something before finding proper material, and the piece was inexpensive. The walls are very thick and theres an 1/8 hole running through...
  10. Replies
    18
    Views
    3,902

    Agree with JediCarpet, I'm in love with this....

    Agree with JediCarpet, I'm in love with this. Absolutely incredible. Props!
  11. Replies
    3
    Views
    1,035

    Heatsink Extension

    Hey all, Firestorm here,

    I'm using a Quad Cree for my build, and it gets VERY hot. I decided that I felt that the V3 Heatsink did not make enough contact with the inside of the choke section to...
  12. Replies
    14
    Views
    3,760

    ^^ This is what I meant. I know full well there's...

    ^^ This is what I meant. I know full well there's no legal backing behind it



    Yeah, that bothered me for a while... I considered using a paperclip and epoxy to fill the hole, but it seemed like...
  13. Replies
    10
    Views
    1,693

    I'll let you know how it goes

    I'll let you know how it goes
  14. Replies
    10
    Views
    1,693

    Whoa whoa whoa, you lost me. I was hoping to be...

    Whoa whoa whoa, you lost me. I was hoping to be able to do the design in illustrator, but I'm not following with "scanning and tracing." If at all possible, I want to cut out possibility of human...
  15. Replies
    10
    Views
    1,693

    Etching design on tapered pieces

    Hello all!

    I've run into a bit of a snag in designing etches for my saber. Specifically, this piece;
    ...
  16. Replies
    438
    Views
    242,650

    Sticky: oOoOoOoOoOoOoOoOoOoOo, +1

    oOoOoOoOoOoOoOoOoOoOo, +1
  17. Replies
    438
    Views
    242,650

    Sticky: Currently we have 2 inch double female, 3in. DF,...

    Currently we have 2 inch double female, 3in. DF, 4in. DF, etc....I'd love to see 2 inch, 2.5 inch, 3 inch, 3.5 inch, etc.
    So....half inch increments in extension sizes!
  18. Replies
    14
    Views
    3,760

    Very true, I only meant that I'd never seen a...

    Very true, I only meant that I'd never seen a plug using this specific idea, with the DC brushless motor casings
  19. Replies
    14
    Views
    3,760

    Blade Plug

    Hello there saber fans! I came up with a blade plug idea, and unless I'm mistaken, it is the first of its kind! I used the motor casing for a small 12v DC brushless motor- The kind that opens and...
Results 1 to 19 of 19