Search:

Type: Posts; User: Cire Yeldarb

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    1,043

    Glad to hear it! :D

    Glad to hear it! :D
  2. Replies
    12
    Views
    2,107

    I was not here a decade ago to remember you, but...

    I was not here a decade ago to remember you, but welcome back! :D
  3. Replies
    3
    Views
    1,043

    Taken from this thread...

    Taken from this thread on the subject, suggestions include:

    Use a C Clamp to press the two sides of the switch plates together. That should reduce the pressure on the pin and allow it to slip out...
  4. Replies
    11
    Views
    1,881

    I bought a SF empty, for the same reason you plan...

    I bought a SF empty, for the same reason you plan to, and the quality of the hilt is "ehh".

    There are some sharp edges that can cut you if you're not careful before you sand them down, the pieces...
  5. Replies
    10
    Views
    1,787

    I actually really like the pattern that makes!

    I actually really like the pattern that makes!
  6. Replies
    13
    Views
    2,653

    Good luck on the costume indeed! I myself am...

    Good luck on the costume indeed! I myself am working on an ROTJ, but at a snail's pace haha
  7. Replies
    12
    Views
    2,766

    Nice! I'm always a fan of a shiny saber!

    Nice! I'm always a fan of a shiny saber!
  8. Replies
    2
    Views
    640

    I see blasters semi-regularly at goodwill/savers...

    I see blasters semi-regularly at goodwill/savers type establishments, that is where i would head first
  9. Replies
    7
    Views
    1,823

    I'm just curious why you slit the hose?...

    I'm just curious why you slit the hose? Especially since you showed that it fits over the 3/4 blade fine in one piece (if a little tough to get on, but that just means it would be more secure in my...
  10. Replies
    10
    Views
    1,787

    As I am sure you found, the stock MR board is not...

    As I am sure you found, the stock MR board is not capable of running more than 1 individual LED at full brightness; adding others decreases the current going to each
  11. Thread: Greetings

    by Cire Yeldarb
    Replies
    9
    Views
    1,429

    http://www.thecustomsabershop.com/Chassis-Parts-C7...

    http://www.thecustomsabershop.com/Chassis-Parts-C74.aspx
  12. Replies
    2
    Views
    1,596

    I don't recall anyone specifically doing UV...

    I don't recall anyone specifically doing UV reactive paint with their UV lights, but others have tried adding UV LEDs in general

    See for more information:
    Latest Board
    Slightly older Board...
  13. Replies
    21
    Views
    2,738

    is the battery all charged up? sometimes...

    is the battery all charged up? sometimes continuous swings/clashes like that are caused by low battery
  14. Replies
    3
    Views
    886

    Niiice! I have all 4 of these, and the Sith one...

    Niiice! I have all 4 of these, and the Sith one is definitely my favorite!
  15. Replies
    8
    Views
    1,469

    Ace beat me to it, and with a very complete...

    Ace beat me to it, and with a very complete response!
  16. Replies
    8
    Views
    1,469

    Except for the blank ones, which are what he is...

    Except for the blank ones, which are what he is asking about. Unfortunately, I do not know the answer...
  17. Thread: Help!

    by Cire Yeldarb
    Replies
    16
    Views
    2,179

    Okay so your problems definitely seem to be no...

    Okay so your problems definitely seem to be no resistor on the Switch LED (might be too late), and no diffusion material in your blade!

    When jbkuma says clear gift wrap, he is referring to...
  18. Replies
    9
    Views
    2,147

    You list 16mm AV switch hole up by the hilt, but...

    You list 16mm AV switch hole up by the hilt, but 12mm AV switch down below, just make sure you order the right size hole for your switch or Vice versa.

    Also, if your switch is illuminated you'll...
  19. Replies
    6
    Views
    3,545

    I personally have used all 3; the Diffuser Tube,...

    I personally have used all 3; the Diffuser Tube, the Blade Film, and Cellophane.

    Personally, I think 6+ feet of Cellophane wrapped in a couple wraps of Blade Film looks best, but that is just my...
  20. Replies
    3
    Views
    825

    Process would be similar to that discussed here...

    Process would be similar to that discussed here, but the details may change depending on what exactly you are looking to upgrade and/or what you are looking to reuse from the stock parts.
  21. Replies
    3
    Views
    1,271

    have you looked in your config file yet?

    have you looked in your config file yet?
  22. Thread: Pommel 4

    by Cire Yeldarb
    Replies
    2
    Views
    738

    "Pommel 4", or "MPS Pommel 4"? I can speak for...

    "Pommel 4", or "MPS Pommel 4"?

    I can speak for certain that MPS Pommel 4 has the standard ID all the way to the end, no different than any other MPS Pommel.
    Cannot speak for "Pommel 4", but it...
  23. Replies
    13
    Views
    1,781

    pictures of your wiring would probably be helpful...

    pictures of your wiring would probably be helpful in the diagnosis process if you can get them!
  24. Replies
    5
    Views
    1,326

    Either way works, it's whatever you are more...

    Either way works, it's whatever you are more comfortable with.
  25. Replies
    13
    Views
    2,946

    Looks great!

    Looks great!
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4