Search:

Type: Posts; User: Anghelos

Search: Search took 0.00 seconds.

  1. thx for the advice, was already my idea to...

    thx for the advice, was already my idea to isolate it, but i also tried to swing the hilt keeping the mosfet away and isolated with some duct tape just in case....still the same issue :|
  2. I already use a plastic pipe to avoid the exposed...

    I already use a plastic pipe to avoid the exposed wiring to touch the aluminium... in the dropbox there are pics about :)
  3. Problem with custom hilt and 2015 hasbro electronic saber

    Hello!
    After lots of weeks of works i finally managed to prepare my hilt with inside the hasbro board, problem is...that doesn't work properly.
    While outside the hilt or just inside the hasbro...
  4. Replies
    0
    Views
    2,458

    rgb led and rotary switch problem

    Hello again...
    While i was making my test according with mu old schema, i found out that I couldn t switch to different color....every time my blade was always white.
    This happens because the...
  5. https://www.dropbox.com/s/3t731unoina6nbu/CircuitH...

    https://www.dropbox.com/s/3t731unoina6nbu/CircuitHasbro%20-%20RGB.png?dl=0

    So, as you can see my diagram is slightly different, mostly because i use a different recharge port (a micro usb) and a...
  6. Badly, my configuration is a bit different: I...

    Badly, my configuration is a bit different:
    I ordered a rotary switch 8 position 1 way to cycle the colors through it, so i can decide what color i want to show during my usage.
    now, in order to...
  7. Can u post a short video about? So when the...

    Can u post a short video about?
    So when the bladr is hit or lit u have the multicolor blade?
    And u have this attaching the pnp base to spk neg?
  8. changing the 'hit' effect on hasbro 2015 board?

    Hello,
    As most of u know, when hitting with a bladebuilder hasbro 2015 the effect on the blade is a flickering: basically the light turn off and on rapidly to make the effect. I want to avoid...
  9. Replies
    2
    Views
    13,562

    Pilot the Led with a slider?

    Hello again,
    I was making some tries on my blade and led, and found out that if I attach a Trimmer / potentiometer to manage the light, it give a nice opening and closing effect, very similar to...
  10. the bypass speaker solution seems the best for...

    the bypass speaker solution seems the best for the moment :D
  11. oh...I see... The usb charger should have the...

    oh...I see...

    The usb charger should have the protection (or at least i hope so ^^') but the battery does anyway.
    If u say that it uses so low current, then i think i will apply this idea....
    ...
  12. that's a very good idea actually! But I wanted...

    that's a very good idea actually!
    But I wanted to use the less energy possible, so, I want to bypass completely all the soundboard....I fear that with this idea i might still have the soundboard...
  13. https://www.dropbox.com/s/n262gbv4xvk7ff5/CircuitH...

    https://www.dropbox.com/s/n262gbv4xvk7ff5/CircuitHasbro.png?dl=0 let's try like this ;)
  14. Hasbro2015 Schematic + micro USB recharger question

    Hello everybody :)
    I'm trying to make my own lightsaber with sound using the Hasbro Luke Skywalker bladebuilders 2015 LB.
    I wanted also to add a rechargable battery with a micro-usb so I don't have...
Results 1 to 14 of 14