Search:

Type: Posts; User: Gorth

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    3,262

    Problem with creating custom font

    I'm using a nano biscotte v3 and wanted to create a cusotm sound font. I created sound files in audacity making sure they were mono and wav, I formatted the sd card then pasted all banks onto the sd...
  2. Thread: Testing Speaker

    by Gorth
    Replies
    3
    Views
    12,968

    Well you can always connect the battery and a...

    Well you can always connect the battery and a switch to the board then touch the two sides of the speaker to the board. When I tested mine, I really just taped everything together or used a bread...
  3. Replies
    4
    Views
    2,390

    Can we get some pictures or a schematic? Is it...

    Can we get some pictures or a schematic? Is it all put together?
  4. Replies
    4
    Views
    4,250

    I've only done one NB3 but to my knowledge, the...

    I've only done one NB3 but to my knowledge, the speaker doesn't matter which way it is polarized. Even if it did, couldn't you just unsolder them and resolder. If you cross soldered and need it...
  5. Thread: New NBv3 Problem

    by Gorth
    Replies
    4
    Views
    2,481

    If you use jst's, don't trust them. Try doing...

    If you use jst's, don't trust them. Try doing some tests like just hooking up the battery to the board and the speakers, this might help to find the area of problem. If you have a breadboard, it...
  6. Replies
    4
    Views
    4,472

    For anyone's future reference, I did various...

    For anyone's future reference, I did various tests to find the site of the faulty connection and I think it was the female side. So I jammed a pin into the locking mechanism, ripped the wires with...
  7. Replies
    4
    Views
    4,472

    Switch and jst not working

    I have an av switch connected to my NB3 by a jst and it often doesn't work. If I put wires in the jst and manually put them where they need to be , the switch works, so I know the switch works. It's...
  8. Replies
    9
    Views
    5,854

    Does the NB3 always supply 3.7 to the led?

    When reading the manual, I noticed an option to change the voltage supplied to the led, does this mean the board will always supply the same voltage (3.7) or is it just whatever the battery supplies....
  9. Replies
    4
    Views
    17,305

    There is one negetive that goes to the battery...

    There is one negetive that goes to the battery and one which goes to the board, maybe these are switched on yours. You could try switching these. The only other possibility I can think of is that the...
  10. Thread: Wiring check

    by Gorth
    Replies
    7
    Views
    3,688

    Your resistor values seem very high. My av switch...

    Your resistor values seem very high. My av switch only required like a 15 ohm resistor and the main led was less than .5ohm.
  11. Replies
    3
    Views
    3,862

    Sound font suggestions

    I'm looking for some unique sound fonts. I really like the very electrical sounding ones like, ancient saber, or really bassy ones would be cool too. Just tell me your favorites because there are so...
  12. Replies
    33
    Views
    12,211

    You could also put small resistors in parallel or...

    You could also put small resistors in parallel or larger resistors in series. For example for your blue led, having two .5ohm resistors in parallel would give you .25 ohm resistance which is much...
  13. Replies
    33
    Views
    12,211

    Actually if you read the manual, any led that...

    Actually if you read the manual, any led that only needs a small resistor (<.5ohm) you can change the drive to the led from the board to less than 1Amp, so you can max out the possible current going...
  14. Replies
    0
    Views
    11,942

    How to connect nano biscotte v3 to 12w led

    I don't know if I have to do a hack like the last version or how the use the on board pex, please help
  15. Replies
    3
    Views
    4,296

    How to connect nano biscotte v3 to 12w led

    I know for previous versions of the nano biscotte a pex hack was required but apparently, the v3 already has a pex. So what I don't know is how to use the pex that is installed and If I have to do...
Results 1 to 15 of 15