yeah i literally just got back from michaels. i got the 40" by 100' clear gift wrap. i put in probably about 2 feet, ill add more and see if i like it. so i figured full power RGrB would make white,...
Type: Posts; User: Ambrosius Malachai
yeah i literally just got back from michaels. i got the 40" by 100' clear gift wrap. i put in probably about 2 feet, ill add more and see if i like it. so i figured full power RGrB would make white,...
well i have a trans white blade, with corbin film and its still doing it. is the trans white any good? or should i lightly sand a clear poly blade? im planning on getting polypropylene to add to the...
ok heres the vid.
https://www.youtube.com/watch?v=DQVZ6dKLUtM
now where in the hell do i get a solid nylon tube like that? everywhere i look, no matter what i search for - all i get is nylon...
it worked. which is retarded since thats backwards from how its own manual says to do it.
well i double checked it like 5 times and its wired correctly. the bottom, and longest pin goes to the battery neg, the right pin goes to the underside connection closest to the sd card slot, and...
okay first off, yes its wired correctly. when i have the saber on, and i unplug the rice cable, the saber recognizes it, and reboots. my problem is not getting the program to recognize the saber. now...
so i got my cf wired up. for the most part. See, im using the chasis system and trying to solder when its on the chassis is a pain in the a$$. so i soldered on some small leads to all my connections,...
Thanks!
okay so i just test wired my led, and it wasnt as bright as i had expected. there was a huge dead spot in the blade. So, let me ask this: to test it, i wired the green and rblue of my RGrB, up to the...
hey so i just test wired my led, after taping the heat sink module to the bottom of my blade - (the shop is out of hilt parts, so im waiting on that) - and it didnt light up evenly. im using a 1"...
yeah, thats what the last few comments were about - is figuring what resistors to use. See it doesnt say that in the manual. It just says about doing it with a single cell, and doenst specify if it...
alright one other thing. in the color mixing without the Cex part, as well as the converting for single cell use - it states that converting it for single cell use allows for direct drive (pseudo...
so then would it be safe to use the 3.9ohm 5w resistor in TCSS? Also, what is with the wattage of resistors? is the 5w just like a max rating? or will using a resistor with higher wattage like say a...
well anyways, i went and used the formula the manual gives for calculating resistors - and i also used an online led resistor calculator - and got different answers. the manual says; R = (Vpack – Vf...
You take what im saying as an insult. I am not saying you are incorrect. The human brain is completely incapable of "new" ideas. It can only combine what it already knows. Every advancement of...
i have no idea what drive parameter for non current regulated channels is, or what regulated channels are. If you would please explain
i may not know electronics, but i know physics and common sense. if it isnt a flaw, then why does it give out 500ma more power than any die can handle? why intentionally give enough power to break...
okay so i already know that the resistors are to limit the current going to the dice in order to stop them from getting more power than they can handle. Now to figure out how to apply what you said -...
okay so i have read through the manual again, and it is saying that not only will it not have great color mixing, but that for the foc and using the other dice channels, that i should keep the...
so then does that mean i have to wire it exactly as shown, with red as the main color, or do i then tell the board what color is wired where, using rice?
yeah, but it has two dies going to foc, and the main die as the red one, will that still give full color mixing
Hey guys so, i am building my first saber. I was originally planning on using the petit crouton, but i ended up getting enough extra money that i went ahead and bought the new CF V8. The only problem...
alright, i was wondering about that, i had seen some talk of a CF-LS, but never when talking about the led's. only ever about its special effects and sound capabilities. So all in all though, do i...
sort of. i finally found a picture of a set of 2 serialized led chunks, wired up. so let me break it down how i see it, just to be sure
so, i take my total number of led's and divide them into 6...
okay, so ive seen the string blades. found some nice bright, 120 degree led's. but before i finish my decision on either a string blade or mounted led, how the hell do you wire them for the scroll...