Search:

Type: Posts; User: Ben Elion

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    1,437

    7.4v Li-ion 1600mAh 14500 Battery Pack

    Hi,

    does this pack have a special 2S2P pcb or are the parallel connected cells charged and monitored as two cells with 1600mAh?
  2. Replies
    12
    Views
    7,646

    I hope we didn´t have a misunderstanding here...

    I hope we didn´t have a misunderstanding here caused by my unability to find the right words (and grammar) in English.
    Your comments sound to me like you´ve been attacked personally, but this could...
  3. Replies
    12
    Views
    7,646

    Ok, I have two Ledengins here, which I ordered...

    Ok,
    I have two Ledengins here, which I ordered from TCSS December last year.
    One RGBA, one RGBW and had three pads in total (especially the smaller ones) coming off.
    It may happen because we had...
  4. Replies
    12
    Views
    7,646

    It is not only frustration and we had it running...

    It is not only frustration and we had it running before.
    But I wasn´t satisfied with the colour and wanted to switch from B+G to B+W.
    When I was desoldering the pad from the serial bridge, the pad...
  5. Replies
    12
    Views
    7,646

    In my opinion and as statement from my wife, who...

    In my opinion and as statement from my wife, who is an electronic technician with certificates in SMD and other solder techniques, the Ledengin PCB is the worst thing we ever had to solder.
    The pads...
  6. Thread: Overdriving

    by Ben Elion
    Replies
    14
    Views
    5,722

    Afaik the newer red P4 blows quite fast, when you...

    Afaik the newer red P4 blows quite fast, when you push it too far.

    Specs say typ. 350 to 800 mA max., so I wouldn´t drive it higher than 1000mA.
    But even this could be too much.
  7. These are the same batteries that I use. Same...

    These are the same batteries that I use.
    Same with the PCB, but it got from another dealer.
    This type is offered by many shops.
  8. Hi, Bertuzzi this saber looks good so far....

    Hi, Bertuzzi

    this saber looks good so far.
    Great work, especially because it is really handmade.

    Is this only the green die of a Cree RGB?
    Which Cree is that, as the one I tested (MC-E) had...
  9. Replies
    8
    Views
    4,445

    Yesterday the green 5W Huey Jann LEDs finally...

    Yesterday the green 5W Huey Jann LEDs finally arrived and I put them into my custom.

    OMG, these are bright and provide a nice green!!

    The P4 has a lite minty green, while the Huey Jann has a...
  10. Replies
    8
    Views
    4,445

    Thank you Boj-Vaati. If you´re used to hold...

    Thank you Boj-Vaati.

    If you´re used to hold and use the lightsaber like a katana, it is working great with the buttons.

    I´ve tested the handling last weekend in a wild unstructured fight.
    My...
  11. Replies
    8
    Views
    4,445

    Thank you. I just wasn´t sure about the...

    Thank you.

    I just wasn´t sure about the auto-sense of the voltage, especially below 3V.
  12. Replies
    8
    Views
    4,445

    Vilpuus 1st custom and some questions

    Hi,

    just finished my first custom:

    Parts:
    - Empty hilt from JK-Sabers
    - Huey Jann 5W blue LED
    - PC-L Lightmeat
    - Samsung 18650 protected 2600mAh
    - very small and short momentary vandal...
  13. Replies
    31
    Views
    73,223

    I had some small difficulties, which are hard for...

    I had some small difficulties, which are hard for me to explain in english.
    But I will try



    This didn´t work for me at all.
    The golden ring and the grip had been like glued together.

    The...
  14. Replies
    31
    Views
    73,223

    Hm, I hope a DX RGB will be enough to get an even...

    Hm, I hope a DX RGB will be enough to get an even lit blade.
    The brightness and colour mix of the Seoul P5 had been very disappointing.

    In my opinion the new Mace is much more durable than the MR...
  15. Replies
    31
    Views
    73,223

    Great tutorial. This helped me to convert my...

    Great tutorial.

    This helped me to convert my Mace too.
    Without it, I never would have dared to do the conversion.

    BTW
    Which RGB LED did you use?
    It is a little unusual to put the resistor on...
Results 1 to 15 of 15