Search:

Type: Posts; User: Forgetful Jedi Knight

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    8
    Views
    62

    For what you have planned, it looks fine.

    For what you have planned, it looks fine.
  2. Older boards like that DO NOT support Smooth...

    Older boards like that DO NOT support Smooth Swing. Thatís why youíre having issues.
  3. Replies
    8
    Views
    62

    Thatís the main thing. You might need other...

    Thatís the main thing. You might need other resistors, but until you fix the picture, I canít see it well enough to tell you. 😉
  4. Replies
    8
    Views
    62

    To post pics, usually you host it offsite, and...

    To post pics, usually you host it offsite, and post a BBCode link.

    For the Neopixel blade, the resistor goes on the blade side PCB
  5. No. I believe itís under Crystal Focus Sound...

    No. I believe itís under Crystal Focus Sound Fonts.
  6. You can go through the archives on Plecter Labs...

    You can go through the archives on Plecter Labs website and download the SD card contents there.
  7. Welcome to the forums. Offhand Iíd say the...

    Welcome to the forums.

    Offhand Iíd say the battery amperage was insufficient. You need a 15A battery to run a setup like that.

    In case you werenít aware, these forums are attached to a site...
  8. Iíd have to research the various wiring diagrams,...

    Iíd have to research the various wiring diagrams, but I donít think so. You add the resistor to help protect the LEDs themselves, and also, a 50 cent resistor is way cheaper than replacing a GGW...
  9. Each LED should have its own resistor.

    Each LED should have its own resistor.
  10. You likely have a switch issue, or you have it...

    You likely have a switch issue, or you have it set so that you have to hold the switch down for a couple of seconds to turn off.
  11. What are you referring to?

    What are you referring to?
  12. That board isnít sold here at TCSS, so I donít...

    That board isnít sold here at TCSS, so I donít believe that youíre going to find many, of any people here who will be able to really help you out.
  13. What kind of battery SPECIFICALLY are you using?

    What kind of battery SPECIFICALLY are you using?
  14. You can use a trim ring if there already is a...

    You can use a trim ring if there already is a gap, but normally there shouldn’t be one. I would actually put it together with the heatsink inside before making any decisions.
  15. Since thatís not a board thatís sold by TCSS, Iím...

    Since thatís not a board thatís sold by TCSS, Iím not sure that youíre going to find a lot of people on this forum who will be able to help you out. I suggest you check whatever manual came with that...
  16. I redid it without the audio......

    I redid it without the audio...
    https://youtu.be/nEaLd4riIkw
  17. Welcome to the Forums. how long is that hilt?...

    Welcome to the Forums.

    how long is that hilt? Because I honestly donít see either way being practical. You have left no room for any wires. You can have the CFX in either direction, though I try...
  18. Replies
    3
    Views
    594

    You let go for a second, and then press it...

    You let go for a second, and then press it quickly to advance to the next font.
  19. Replies
    3
    Views
    594

    As soon as you access the sound menu, you let go...

    As soon as you access the sound menu, you let go of the aux button, and quickly tap the aux button to go to the next font.
  20. Replies
    1
    Views
    449

    Usually you hit the floor with it. You also have...

    Usually you hit the floor with it. You also have to make sure you have the drag angels set properly.
  21. If the battery doesn’t slide around too easily,...

    If the battery doesn’t slide around too easily, then you’re good. The fact that you have that little blocker there is good.
    id be more concerned about accessing the chassis as a while, once...
  22. No. Which is why I suggested before turning the...

    No. Which is why I suggested before turning the saber off, manually set it for the font you want to turn on to.
  23. You have to set the saber to the font (and...

    You have to set the saber to the font (and color/effect, etc) that you want it to go back to, and then leave it there.
  24. Replies
    1
    Views
    454

    No, those canít be disabled as far as I know.

    No, those canít be disabled as far as I know.
  25. Replies
    1
    Views
    438

    I have no idea. That pressing the aux button...

    I have no idea.

    That pressing the aux button and the blade lighting up half way IS the PLI function youíre looking for.

    I always adjust the volume by manually editing the SD card.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4