Search:

Type: Posts; User: lovetadraw

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    215

    For a rusty look, I like to use hammered bronze...

    For a rusty look, I like to use hammered bronze spray paint sprayed from a good distance away.
  2. The 3.3v power indicator pad or the DS pad.

    The 3.3v power indicator pad or the DS pad.
  3. Replies
    3
    Views
    491

    I found that even the v6 works if you cut off the...

    I found that even the v6 works if you cut off the speaker part and sand the main part slightly.
  4. Replies
    3
    Views
    1,599

    I would grind it down, but beware, one good hit...

    I would grind it down, but beware, one good hit during a duel can snap some of them off.
  5. Replies
    14
    Views
    1,303

    I'll be honest, I'm not a brightness junky. My...

    I'll be honest, I'm not a brightness junky. My first build was a PVC stunt with a single deep-red rebel. However, a few months back I decided to play around with a QuadCree for a 3 channel NBv3 saber...
  6. Replies
    7
    Views
    642

    I had a similar problem with a mistake while...

    I had a similar problem with a mistake while wiring a recharge port, saber worked great till I charged it stopped working.
  7. I recently ordered a trans-white 7/8" blade and...

    I recently ordered a trans-white 7/8" blade and asked for them to ship it with 1" thick walled diffuser in it. It fit for me.
  8. Replies
    10
    Views
    2,089

    You can also make chassis from 1" blade material.

    You can also make chassis from 1" blade material.
  9. George I believe said that lightsabers would seem...

    George I believe said that lightsabers would seem to exhibit a lot of weight, so HG blades would be that.
  10. Replies
    8
    Views
    4,124

    I've hard dueled with mine, held up just fine.

    I've hard dueled with mine, held up just fine.
  11. I'd be careful of using the 15a batteries in the...

    I'd be careful of using the 15a batteries in the Keystone holders, I tried that and it snapped. Twice, one from TCSS and a spare I had lying around.
  12. Replies
    2
    Views
    3,907

    Its a removable cell so you don't use a RCP. I...

    Its a removable cell so you don't use a RCP. I suppose one could modify it and put in a static cell and do an RCP, but I wouldn't.

    Not sure, I assume so.

    You set the drive values in the...
  13. Replies
    2
    Views
    3,608

    I would imagine yes. I had them do a guarded...

    I would imagine yes. I had them do a guarded switch hole in the luke style ribbed section.
  14. Being deep red, it'll be a little dimmer, but the...

    Being deep red, it'll be a little dimmer, but the color is a more true purple. I do most of my RGB setups with deep reds.
  15. Replies
    13
    Views
    1,573

    "Teslatechguy has chosen not to receive private...

    "Teslatechguy has chosen not to receive private messages or may not be allowed to receive private messages. Therefore you may not send your message to him/her." :/
  16. Replies
    13
    Views
    1,573

    I just wired an NBv4 with two reds on a...

    I just wired an NBv4 with two reds on a quad-cree. (dR+R/rB/pcA, very strong full red, cool FoC options) The hardest part was wiring the leds because the MHS heatsinks don't have a center hole so...
  17. Replies
    7
    Views
    1,010

    I find if you do standard R/G/rB you get a...

    I find if you do standard R/G/rB you get a pinkish white. When I do dR/G/rB it's a snowy silver and I love it. So I'd say max them/make them equal (battery save) and then lower the red as desired.
  18. Replies
    2
    Views
    894

    Depending on the color, I like clear blades or...

    Depending on the color, I like clear blades or transwhite. I like cellophane the way some other guys d their blade film.

    For a 3D print, I'd get a 1" heatsink and leave room for it.

    2" or...
  19. Replies
    431
    Views
    233,189

    Sticky: Speaker holders for 20mm speakers for use with...

    Speaker holders for 20mm speakers for use with 1.15 and/or MHSv2 hilts
  20. Replies
    13
    Views
    1,911

    I believe Madcow says in one of TCSS's videos...

    I believe Madcow says in one of TCSS's videos that Sinktube works well to make it a tight fit on the body.
  21. Replies
    431
    Views
    233,189

    Sticky: 2nd this. Also, I think a variant on the v6 with...

    2nd this. Also, I think a variant on the v6 with the lip further back emulating the disk chassis style with the lock disk behind the speaker would be nice. I like the speaker close to the grill, and...
  22. Replies
    11
    Views
    1,801

    Prizm is sound and driving (minus one channel),...

    Prizm is sound and driving (minus one channel), Emerald is just sound driver, and requires 7.4v, and is frickin' huge, no accent leds, no sd card.
  23. Replies
    2
    Views
    539

    Even though Green crees run at 3.7v just fine, I...

    Even though Green crees run at 3.7v just fine, I always through the .47ohm resistor on there, just in case.
  24. Yeah, I'm weighing some options since they are...

    Yeah, I'm weighing some options since they are still out. I had a v5 on hand last time which I ground the lip off of. One might have hoped they'd have restocked in the last 2 months or so but...
  25. Replies
    29
    Views
    3,298

    If you want, I've also seen people use non...

    If you want, I've also seen people use non removable batteries in that chassis.
Results 1 to 25 of 73
Page 1 of 3 1 2 3