Sorry for the dealy(Darth Real Life)
The motor is a 3.5 v motor
Type: Posts; User: Salohcin0083
Sorry for the dealy(Darth Real Life)
The motor is a 3.5 v motor
I have to go by radio shack to find out the specs-
No resistor on it-
Ive wired an exact motor match to a previous build(exact wiring schematic as well) where the only difference was I used a...
Hey guys,
I wanna check if this is correct- I've successfully built this build before with the exception of the recharge port.
I want to check if I'm doing it correctly because after wiring it...
I applied the heat shrink to the recharge port legs-As well as confirmed my green LED still works and the wiring allows the LED to activate-
Unfortunately still no response from the green when the...
I'll heat shrink the recharge port legs-
I am able to test the Green LED with a separate 3 v battery pack. I installed the kill key-I ran the leads from the separate battery pack to the ends of...
Shoot sorry knight-
I have had the saber working for the last 3 months or so-
I lost function of the green LED after installing the recharge port-
I have the colors set up on the 3 different...
I got a pre-made battery pack from the TCSS store
7.4v Li-ion 1050mAh 14650 Battery Pack- Item #7414650
I am not against trying that-
Just to confirm though- The saber does not just cut out- It will do a full power down as if I just deactivated the saber with the power button-
If it was low/out...
Hi Knight,
I added some more info to the original post,
Essentially- I used a battery pack at the board ned/pos and FOC3 pad to confirm wiring/soldering -that worked to ignite LED3. I checked...
Hello All,
I was going to rewire my FOC3 today after breaking the connection running my recharge port wires under the board-when I noticed the connection still in tact as well as still putting out...
Hey all,
Basic Part Info
CF 7.0
7.4 v battery pack
GRBA tri cree
I had an operating set up for my cf but needed to shorten it to fit into hilt- When I finished I tried to fire it up but...
Greetings,
A couple pics of what is done so far-Waiting for a ribbed/grooved choke combo to be available to finish up wiring and mock up.
Gonna get rid of LED JST connector once I confirm I have...
I did what you said. Also shortened the leads to be safe. The switch parameter was already set on 2 which if i read correctly is set for momentary,
Fired up on the first try. WOOHOO!!! I was...
Hey Knight,
The parallel accents was just because I haven't read if i can use accent pads to mimic main led, but that is the over all goal.
I have not done anything in the SD card file's yet. I...
Hey there dudes/dudettes,
I inserted a pic of my wiring diagram i plan to use as long as it checks out.
Cree G/RB/A
7.4 volt pack with jst quick disconnect
2 green accent led
rumble motor...
sorry moved to led q and a's
My condolenses. I feel for you. I just finished my first saber after a couple of sleepless nights.
I also had an issue with a missthread and a couple fried econo boards.
Good luck with all to come.
I believe I am at 1 manly.
My first order I forgot the pommel and a couple screws-the second order takes care of that. Hopefully before take your saber to work day I can get this first one all...
So thanks to everyone's help I was able to get the saber to work. But I must have messed up my wiring while getting my crash coarse in cram-fu. Now the main led works and that is it. But instead of...
Yes Rhyen Skytracker I was running into that issue. Thanks. The original plan was to also include the LED driver but I opted to add it a later date due to my lack of expirience. But now it seems that...
Thanks Darth Xusia- and everyones help for that matter.
I feel dumb that I didn't think of this like a regular switch.
I guess I was a little overwelmed by all this- it has been a fun
crash corse...
I think I might have it now. I redid the diagram- does this take care of the power issue for the Main and green accent LED?
And to answer your question skottsaber; Tanimal got it right- i do not...
So I got in the electronics for my first saber build.
Specs:
1 DPDT momentary green illuminated switch
1 SPST momentary switch with black switch(switch05)
hasbro 2010 economy board
1 yellow LED...
Greetings to all,
I was hoping to get some feedback on this build idea. I am looking to have a green saber with an yellow indicator light acting as a flash on clash that is activated with either...
Great looking build. Keep up the awesome work.
Is that the new TCSS constant current LED driver?
If so how do you like it?
I am interested in seeing how it performs.