Search:

Type: Posts; User: Forgetful Jedi Knight

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    11
    Views
    327

    Nice work.

    Nice work.
  2. Replies
    10
    Views
    486

    You donít have nearly enough depth in that blade...

    You donít have nearly enough depth in that blade holder.
  3. Replies
    7
    Views
    375

    No, you wouldnít as far as I know.

    No, you wouldnít as far as I know.
  4. Replies
    7
    Views
    375

    https://www.thecustomsabershop.com/Power-Xtender-2...

    https://www.thecustomsabershop.com/Power-Xtender-20-P652.aspx
  5. Replies
    7
    Views
    375

    Short answer, yes, you’ll need the PEX.

    Short answer, yes, you’ll need the PEX.
  6. Replies
    10
    Views
    486

    Well, you do have to tighten both screws while...

    Well, you do have to tighten both screws while the blade is in. With that said, that is way too shallow for a proper blade depth. Also, a picture of the entire saber would be a bit helpful.
  7. If you have a pommel that has a little depth to...

    If you have a pommel that has a little depth to it, thatís all you should need. Itís all Iíve ever needed.
  8. Replies
    6
    Views
    447

    This might work, if you use speaker holder v4. It...

    This might work, if you use speaker holder v4. It is a way better option than the other suggestion that Iíve seen mentioned (which I would never, EVER recommend).
  9. Replies
    6
    Views
    447

    The locking speaker holder won’t fir. The...

    The locking speaker holder won’t fir. The internal diameter of the chokes are .8” you can get a speaker mount without the threads (I believe it’s speaker holder 4) however, you have to come up with a...
  10. Replies
    6
    Views
    352

    Well, either he is wearing the battery down, or...

    Well, either he is wearing the battery down, or his setup is drawing too much power from the battery. Since “after a while” hasn’t been defined with minutes, it has to be that OR he has a bad/poor...
  11. Replies
    6
    Views
    352

    Again, are we talking about after he turns it off...

    Again, are we talking about after he turns it off using the power button? If that is the case, it IS covered in the manual.

    Otherwise, the saber works just like a normal flashlight, it stays on...
  12. Replies
    6
    Views
    352

    Stay on longer how? After they turn it off? Or...

    Stay on longer how? After they turn it off? Or are they complaining about the runtime?
  13. Replies
    2
    Views
    288

    Iíve never heard of that happen before. In some...

    Iíve never heard of that happen before. In some LEDs the polarity matters, and others it may not, it all depends on the manufacturer.
  14. Replies
    4
    Views
    530

    You should be able to use them on the (-) side,...

    You should be able to use them on the (-) side, BUT the polarity of the dynaohm resistor does matter.
  15. Replies
    4
    Views
    530

    1. Dynaohms arenít meant for main LEDs, just...

    1. Dynaohms arenít meant for main LEDs, just accent LEDs. ;)

    2. Donít adjust the drive settings, just use regular resistors on your main LEDs (math involved).
  16. Itís one resistor per LED. Youíll have to...

    Itís one resistor per LED. Youíll have to obviously replace the resistor.
  17. I’ll send you a PM. Locked - FJK

    I’ll send you a PM.


    Locked - FJK
  18. Replies
    4
    Views
    504

    The do make adapters between the 2 versions. That...

    The do make adapters between the 2 versions. That may work better, if theyíre in stock.
  19. Replies
    4
    Views
    504

    I vaguely remember you. To answer your...

    I vaguely remember you.

    To answer your questions:

    1. Youíd.be better off getting the newer MHS heatsink assembly if your planning on using Tri-Crees.

    2. Yes.

    3. Iíve done it, with no...
  20. You would have to rename the stab sounds as...

    You would have to rename the stab sounds as blaster(whatever number).wav, and use the aux button to trigger it. But the various blaster sounds are random as I recall. So you would have to decide if...
  21. No, there is not a way to use those on a Prizm....

    No, there is not a way to use those on a Prizm. One of the distinguishing factors between the boards were the sound effects that were available per board. Since the Crystal Focus is the top of the...
  22. Replies
    1
    Views
    335

    Usually, yes. You may have to remove your...

    Usually, yes. You may have to remove your override configuration file, or just shift through the profiles until you get what you want. See manual for details.
  23. Heís not. But he does cover Europe (including the...

    Heís not. But he does cover Europe (including the UK).
  24. Since youíre in the UK, you can send it to Erv at...

    Since youíre in the UK, you can send it to Erv at PLECTER Labs. He handles repairs in Europe. Contact him at Plecterlabs.com
  25. When it comes to rounding (especially the...

    When it comes to rounding (especially the wattage) the bigger the wattage value, the physically bigger the resistor will need to be.

    Since you are using White as the FoC, the .5Ohm 1W should be...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4