Search:

Type: Posts; User: Tom Tilmon

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds; generated 23 minute(s) ago.

  1. Thread: First Build

    by Tom Tilmon
    Replies
    11
    Views
    327

    Welcome to the insanity! Great build! Tom

    Welcome to the insanity! Great build!

    Tom
  2. Replies
    7
    Views
    503

    Holy snikees. That is nuts, crazy, insane, and...

    Holy snikees. That is nuts, crazy, insane, and brilliant all at the same time! WOW! Very awesome.
  3. Replies
    8
    Views
    858

    How did that look? I think we're all still...

    How did that look? I think we're all still searching for the better mousetrap. I like my blades, but I still find things about them I don't like. Might be I stare at them too long, and...
  4. Replies
    7
    Views
    418

    Yep, that is precisely what I do. I have used...

    Yep, that is precisely what I do. I have used them in TCSS graflex, MPP, and DV6 blade plugs. In a U, precisely as you perceived, leaving at least one pixel shining towards the blade, while the...
  5. Replies
    7
    Views
    418

    I make neopixel blade plugs using the blade end...

    I make neopixel blade plugs using the blade end PCB on a blade plug. THen I use however many neopixels I can fit in there. You can use just one, but I find you get a better result by putting as...
  6. Ok, that saber deserves a better board! Great...

    Ok, that saber deserves a better board! Great build. Now strip it and put a better board in there! Awesome looking saber for sure! WTG.

    TOm
  7. Absolutely killer saber and inspiration! Awesome...

    Absolutely killer saber and inspiration! Awesome work E57!!!!!!
  8. Replies
    14
    Views
    1,657

    Seth this is awesome. Love it as always!!!!!

    Seth this is awesome. Love it as always!!!!!
  9. Replies
    1
    Views
    697

    3.7 volts. 12 is probably a maximum rating...

    3.7 volts. 12 is probably a maximum rating stamped on there. Figure your resistor for your supply.
  10. Eeek, I haven't logged into SLD in a bit. I've...

    Eeek, I haven't logged into SLD in a bit. I've been too busy building sabers.
  11. Blackcowl, it wasn't clear you were using a prism...

    Blackcowl, it wasn't clear you were using a prism until later on. I have modified the bulb release area for 2 switches in there, and it worked. I then use the old slide switch in the clamp as a...
  12. I have begun my 3 builds. I'm building 3 of...

    I have begun my 3 builds. I'm building 3 of these, and after honing out one of my quillions today.....2.5 hours later, I don't think I'll take on one of these crossguards again. The 3/4 ID on the...
  13. Replies
    14
    Views
    1,657

    I like it, just not as much as the Jedi Killer. ...

    I like it, just not as much as the Jedi Killer. Awesome work again Seth!!!!!
  14. Replies
    7
    Views
    1,701

    The momentary button has a switch wire, and then...

    The momentary button has a switch wire, and then a ground. It looks like your ground is going to negative with the battery negative. I can't see the wiring where you come out of the GND side of...
  15. Replies
    1
    Views
    548

    Awesome work Anvil. Boring out the K4, I bet...

    Awesome work Anvil. Boring out the K4, I bet that was a gut wrenching moment.
  16. Replies
    18
    Views
    3,202

    If you are using an improper battery, this is...

    If you are using an improper battery, this is common because of the high drain neopixels can put on the battery, it may cause the amp to drop out due to lack of power. You must use a battery with...
  17. Glad you got them, hope you are making progress!

    Glad you got them, hope you are making progress!
  18. Hope they get to you soon. I've been thinking...

    Hope they get to you soon. I've been thinking about this, not sure how dual switches will work in the clamp. There needs to be fulcrum between the two so only one activates at a time. Then you...
  19. Replies
    9
    Views
    1,086

    Of course then there is always: Deep Red, Green,...

    Of course then there is always: Deep Red, Green, Royal Blue dR, G, rB ! You can really get some crazy purples with deep red and royal blue.
  20. https://i.imgur.com/KLJ6x8l.jpg

    https://i.imgur.com/KLJ6x8l.jpg
  21. I don't work for TCSS, I'm just a schmo like you....

    I don't work for TCSS, I'm just a schmo like you. I'll drop those switches in an envelope to you. As for blades, for in-hilt builds, I like clear blades with clear cellophane wraps inside. There...
  22. My answers to your questions are in red. I hope...

    My answers to your questions are in red. I hope this helps.
  23. sounds familiar, on the aux button jewel fiasco. ...

    sounds familiar, on the aux button jewel fiasco. Been there, done that.
  24. Replies
    7
    Views
    1,412

    Awesome K6!

    Awesome K6!
  25. Thread: Videos

    by Tom Tilmon
    Replies
    49
    Views
    54,696

    Sticky: Absolutely insane design! Awesomely creative. ...

    Absolutely insane design! Awesomely creative. How fragile is the clay once it hardens? Where did you get it?

    TOm
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4