Search:

Ok so yea I had continuity there but not between any main pads. I'll test with a battery tomorrow but when I did it before they are lighted correctly. Mean none were blown or didn't light when...

Yea and I just tried 2 clean never used ones and same thing, the continuity meter beeped. Let me know what you find.

I thought it should have continuity there as solder that dot connects the die...

Ok so I am testing it now.

1. I DO NOT have continuity between the little pads (the meter stayed at 1)
2. I DO HAVE continuity between the little pad, and the + and - closest to the little pads....

Also, those little pads in blue test them against each other and each + and - correct, so hold one lead to the small circle, then test it against every +, -, and other small pad?

Thank you

Thank you very much, I will test it tonight or tomorrow and see. I feel like this might be the key.

Appreciate the help sir

Yea that would be awesome. Thank you very much. Just put a dot where I am supposed to test continuity, I tried to keep the solder on the main pad but still.

Thank you for all the help everyone, if...

I think its a negative from somewhere but I am unsure how to find it/look for it. I don't see any bridges, and the transistor is newly soldered there as I thought that was the issue originally

The L3 wire is going to no where, its cut so it cant touch anything.

Also yes I only have it driving L1-, meaning L2- should not do anything, but this is not the case. When I unplug the kill key...

//Nano Biscotte 4.0
drive=1023,0,0
fdrive=1023,1023,0
focmix=001
resume=0
shmrd=210
shmrp=6
shmrr=13
shmr%=0,50
focd=200

I was going to use L3 if I cannot get L2- to work correctly.

Yes the green and blue is wired. Right now I tested with only L2- hooked up to the green and or blue and both had the issue. So it must be with something pertaining to L2- pad area.

Any ideas?...

it could be stray solder, I checked but I didn't see any but i have bad eyes as it is lol.

I attached a back picture as well, does the arrow area seem to be the issue maybe? I tried to clean it up...

Hi everyone,

I am trying to wire a NBv4 using a tcss tri cree xpe2 rgb led. I am only using the G and b dies of the led. However, when I pull the kill key a little lights leaks out of the green...

Yea I need a few cex to . will they be in soon hopefully ?

Late last night I saw when the cf were added to the website but even though add to cart was clickable it would say the cf or some of its components are out of stock when I added them. Is the stock...

Hi Tim,

will the NBv2 be available to buy today/tomorrow or most likely not?

Thanks

what material and where do you get it for like leather wrap or cloth?

I am looking to make a free spin pommel insert for recharge port in the pommel, and have no idea. With the c-clip pressed against the insert it wont spin, is there a secret to this? Do people just ...

https://mail.google.com/mail/u/0/?ui=2&ik=96bc708170&view=att&th=1396eb3f387de9a7&attid=0.1&disp=thd&realattid=1411574113911531801-1&zw
...

i ordered some 14500 side by side+pc holder chassis discs, and they will nto fit, i have sanded them, is there a trick to this? i am putting it on from the right side, but its just way to tight on...

Ok, well mine after the threads went down quite a bit, so much that a pvc chassis well sanded would not fit. If it is supposed to be like that, how can u make a chassis to fit in there? other then...

no the tcss discs for pc/battery, here http://www.thecustomsabershop.com/Acrylic-Chassis-Disc-for-PC-20-and-14500-side-by-side-pack-P774.aspx after the threads, the ID gets smaller, idk if it was a...

ok guys, so i was wondering, a 4inch double female without holes, there is like a lump, after the threads, causing the actual ID to go smaller, and for some reason tcss chassis discs, or even a pvc...

yea but its like a little nook, so that it stays secure, i dont have a file small enough, and sand paper would do a lot so it would get rid of the nook and have nothing to secure it

im using a cf5.1, which is the exact same width as pc 2.0, but it just is way to tight, mean if i push it i know the board will snap