Search:

Type: Posts; User: Jay-gon Jinn

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    453

    looks like those are all back in stock as of this...

    looks like those are all back in stock as of this morning fellas!
  2. Sticky: Yup, a few are still missing, must be I didn't...

    Yup, a few are still missing, must be I didn't think it was necessary to back up a picture of a screw and a threaded wood insert. :/ (Although both pieces are shown in the center of the first pic.)...
  3. You're most welcome and good luck with it!

    You're most welcome and good luck with it!
  4. I fixed the tutorial's pics....it starts here:...

    I fixed the tutorial's pics....it starts here: http://forums.thecustomsabershop.com/showthread.php?3266-Jay-gon-s-PVC-Hilts-Full-tutorial-on-last-page&p=138540&viewfull=1#post138540
  5. Sticky: I have fixed the pictures for the tutorial...

    I have fixed the pictures for the tutorial section and have added a few notes to bring it a bit more up to date.
  6. Hang on, FJK...fixing at FX first so I can just...

    Hang on, FJK...fixing at FX first so I can just copy/paste the text here. But it is the pvc saber topic here:...
  7. Normally, I would refer you to my pvc saber...

    Normally, I would refer you to my pvc saber topic here at TCSS, but since I refuse to pay photo buckets prices, the pictures in the topic aren't there anymore. I have uploaded the pics to another...
  8. FX-Sabers.com on the forums there. Lot's of info...

    FX-Sabers.com on the forums there. Lot's of info about where to get parts for what you want to do.
  9. Just an FYI, it's bad forum etiquette to post...

    Just an FYI, it's bad forum etiquette to post other places to get saber parts on the the forum here, as this is part of a store that sells saber parts. ;)
  10. Replies
    1
    Views
    344

    What film are you planning to use? Cellophane or...

    What film are you planning to use? Cellophane or the TCSS blade film? Cellophane gift wrap isn't measured in wraps, but in feet. If using that, I'd suggest 4-5 feet. If using the TCSS film, I'd go...
  11. Replies
    3
    Views
    393

    What is your issue with the board? There's...

    What is your issue with the board? There's plenty of people here that have experience with that board that may be able to help.

    EDIT: Never mind, saw your other topic. Carry on.
  12. I have used several of those pommels in the past,...

    I have used several of those pommels in the past, and I can safely say they weren't designed with holding a recharge port in mind. Although the inside surface of the pommel end cap is flat, the way...
  13. That should work, however, in your diagram you...

    That should work, however, in your diagram you have the MWS recharge port backwards...the female connector goes to the battery, the male goes to the buck puck as it has the negative on the switched...
  14. Replies
    11
    Views
    2,022

    No, it does not.

    No, it does not.
  15. I've done FoC on plenty of sabers using an RGB...

    I've done FoC on plenty of sabers using an RGB cree, a fourth white die isn't required for that.
  16. Replies
    10
    Views
    2,347

    That is definitely a work of art....especially...

    That is definitely a work of art....especially love the copper tubing and conduit in the crystal chamber.
  17. Replies
    4
    Views
    1,396

    The blade tubes used by ultrasabers have...

    The blade tubes used by ultrasabers have traditionally been slightly too large to fit in mhs blade sockets. They use a different supplier and the tolerances are slightly larger.
  18. Replies
    1
    Views
    1,058

    I'd say that's a no...those modules are pre-wired...

    I'd say that's a no...those modules are pre-wired MHS led modules and are designed to only fit in the MHSv1 parts.
  19. Replies
    19
    Views
    4,798

    In this picture you have your speaker wired to...

    In this picture you have your speaker wired to the battery input pads: https://i.imgur.com/5kMPFm8.jpg Putting the battery supply through the speaker pads is probably not good for the board.
  20. Replies
    5
    Views
    1,430

    My mistake...saw them in the 7/8" section, ...

    My mistake...saw them in the 7/8" section, figured Tim had some in the 1" sizes too. I can tell you from past experience that the white tips don't light up as well as the clear ones, unless you...
  21. Replies
    5
    Views
    1,430

    White blade tips can be found in the store in the...

    White blade tips can be found in the store in the blade supplies section.
  22. Michael Hudnell = Zook on the forums here, and...

    Michael Hudnell = Zook on the forums here, and CHEWBACCA over on the FX-Sabers forums.
  23. That's the ball bearings in the swing sensors and...

    That's the ball bearings in the swing sensors and is normal.
  24. Replies
    19
    Views
    32,254

    Sticky: It's a loose fit, but yes.

    It's a loose fit, but yes.
  25. Replies
    5
    Views
    2,314

    The RGB Tri-Rebel can still be used with the...

    The RGB Tri-Rebel can still be used with the stock battery pack, but you'll want to use a resistor on the red regardless of whether or not you use either of the other colors. Both of those might...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4