Search:

Type: Posts; User: jbkuma

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    41

    Gorgeous!

    Gorgeous!
  2. Replies
    5
    Views
    80

    Resistors are never "required" they are useful in...

    Resistors are never "required" they are useful in some instances. I use bare pixels all the time without issue.
  3. Replies
    5
    Views
    80

    If you are talking about the pixel crystal,...

    If you are talking about the pixel crystal, simply connect the power and data lines
  4. Replies
    4
    Views
    167

    if it's been damaged enough to pull off the...

    if it's been damaged enough to pull off the resistors I'd be concerned that the pads have been damaged or ripped off the substrate. The damage does some somewhat odd, the resistors should be the...
  5. Replies
    20
    Views
    523

    The closer a hole is to perpendicular to the...

    The closer a hole is to perpendicular to the surface the easier it will be to drill. Any similar design will have the same issue, drilling at an oblique angle is not going to be easy.
  6. Replies
    20
    Views
    523

    I'm going to have to agree with FJK here. If you...

    I'm going to have to agree with FJK here. If you want a nice clean look, you just don't have the tools.

    Unless you are extremely skilled and spend an enormous amount of the shaping the rods, you...
  7. Replies
    3
    Views
    124

    I use these types of LEDs as status indicators...

    I use these types of LEDs as status indicators all the time. Why waste inventory on bi-color LEDs, etc, when you could just wire one of these up? Of course if you were doing production runs it...
  8. Replies
    3
    Views
    124

    Yes, that is fine.

    Yes, that is fine.
  9. You'll probably want to order from a place that...

    You'll probably want to order from a place that promises telescopic fit.
  10. Replies
    2
    Views
    346

    Make sure you buy the correct battery. You need...

    Make sure you buy the correct battery. You need the high amp output versions.
  11. Replies
    2
    Views
    264

    you can look at the plecter labs website for a...

    you can look at the plecter labs website for a comparison
    http://plecterlabs.com/Media/Doc/CompareBoards/plecter_boards.php
  12. Replies
    60
    Views
    2,233

    If you have an old computer ATX supply you can...

    If you have an old computer ATX supply you can use the 5v on that, or any AC-DC supply that can output 5V.

    I'm not sure why you chose to run this at 7.4v but there is a good chance you fried the...
  13. Replies
    10
    Views
    1,294

    I like it.

    I like it.
  14. Replies
    2
    Views
    612

    Your example 14500 will have approximately 7.8Wh...

    Your example 14500 will have approximately 7.8Wh (volts * amp hours = watt hours) while the 18650 will be 11.5Wh. The 18650 has more power available.

    The LEDs will not be brighter unless you plan...
  15. Replies
    1
    Views
    607

    What board are you using, the pixels only do what...

    What board are you using, the pixels only do what they are told.
  16. Replies
    9
    Views
    1,169

    Best way to learn is to have a project you really...

    Best way to learn is to have a project you really want to do and just do it.
  17. I have no idea but you can go to a hardware store...

    I have no idea but you can go to a hardware store and try things from the bins.
  18. Replies
    9
    Views
    1,169

    https://i.imgur.com/27RTKfS.jpg Illustrator...

    https://i.imgur.com/27RTKfS.jpg
    Illustrator Saber Club! I did make this one. Pick one and do it!
  19. Replies
    20
    Views
    1,954

    You do not understand what you are talking about....

    You do not understand what you are talking about. I am very aware of all of these things. You will likely not see a problem right away, and take this as confirmation that you were right, since you...
  20. If it is supported at both ends it should be...

    If it is supported at both ends it should be fine. How do you plan to secure the chassis?
  21. Replies
    20
    Views
    1,954

    The load needs to be disconnected so the charger...

    The load needs to be disconnected so the charger can detect the state of the battery. If you have a load drawing off the circuit while it's charging you risk damaging the battery by either over...
  22. Replies
    20
    Views
    1,954

    This is only meant as a charger, not to support a...

    This is only meant as a charger, not to support a load of any kind. To use this you would disconnect the battery from your project and connect it to this charger.
  23. Replies
    20
    Views
    1,954

    Which charger are you looking at?

    Which charger are you looking at?
  24. Replies
    20
    Views
    1,954

    An in-hilt will draw anywhere from 1-5A and a...

    An in-hilt will draw anywhere from 1-5A and a pixel blade will be about 3-8A for a 120x2 pixel blade typically. Longer pixel blades and different configurations will provide different results.

    I...
  25. Replies
    20
    Views
    1,954

    You want your battery disconnected from...

    You want your battery disconnected from everything else when you are charging, that is why many use a charge port. There are USB chargers that have built in load pads, but those are usually limited...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4