Search:

Type: Posts; User: jbkuma

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Illumicore

    by jbkuma
    Replies
    9
    Views
    1,509

    You should probably run separate power lines, or...

    You should probably run separate power lines, or bring the power lines from the blade back to the crystal. If you do wire it through the crystal, make sure you solder the wires together, don't rely...
  2. Replies
    13
    Views
    207

    You should read the manual carefully. Nothing...

    You should read the manual carefully.

    Nothing bad will happen as long as you follow the manual, because 2 LEDs is well within the ratings of the NBV4.

    You made to use two power extenders. I'm...
  3. Replies
    13
    Views
    207

    Actually, the NBV4 should be able to run it fine....

    Actually, the NBV4 should be able to run it fine. The MOSFETs were upgraded from previous versions to be able to support controlling power to a pixel blades. You should really be able to run more...
  4. Replies
    6
    Views
    196

    Depending on what you students are learning you...

    Depending on what you students are learning you may want to look at the FX-SaberOS project. Open source Arduino based lightsaber electronics. The main components are an Arduino, mpu6050, and...
  5. Replies
    6
    Views
    196

    You can buy clear pvc, you'll probably want to...

    You can buy clear pvc, you'll probably want to search for "architectural pvc" the main advantage over polycarbonate and acrylic is that it is less likely to break and easier to work with because it...
  6. Soldering through makes it easier to solder to...

    Soldering through makes it easier to solder to both sides since the wire is less likely to ping off, although one side would usually be surface.
  7. if you only have to make small adjustments use...

    if you only have to make small adjustments use small files, you'll have more control and less likely for things to go horribly wrong.
  8. Replies
    5
    Views
    436

    Your 7.4 battery is destroying the pixels, you...

    Your 7.4 battery is destroying the pixels, you need a single cell.
  9. Replies
    4
    Views
    363

    soon enough your burners go 8 deep and 12 wide.

    soon enough your burners go 8 deep and 12 wide.
  10. Replies
    3
    Views
    474

    Even if the rated forward voltages are accurate,...

    Even if the rated forward voltages are accurate, the green will operate at around 2A at 4+v. While communal experience will say that it will survive, it's still not ideal. The old "wisdom" that the...
  11. Replies
    3
    Views
    474

    I think a lot of people like to psych people out...

    I think a lot of people like to psych people out of the crystal chamber, but I don't see why. I'm sure you can do it.

    As far as I can tell the diagram looks fine. You should have resistors on...
  12. Replies
    13
    Views
    918

    I always feel like I should be documenting how I...

    I always feel like I should be documenting how I do things for some reason, which is one of the reasons I don't post as many of my creations as I should. The organic process of making things is what...
  13. Replies
    8
    Views
    781

    Very nice, I love seeing sabers take inspiration...

    Very nice, I love seeing sabers take inspiration from unique sources!
  14. Replies
    7
    Views
    613

    if you put a half inch piece of PVC inside it is...

    if you put a half inch piece of PVC inside it is almost the same OD as the blade's ID and use a pipe cutter. It will be clean and have a nice rounded edge. No dust to worry about....
  15. Replies
    1
    Views
    692

    Yes. You don't have to do anything, but that is...

    Yes. You don't have to do anything, but that is recommended for a reason. I personally use 20awg. This has nothing to do with the CFX, it's physics.
  16. Replies
    57
    Views
    11,157

    Sticky: Ah well, sadly I've been waiting on parts to...

    Ah well, sadly I've been waiting on parts to arrive for a couple of months :(

    I'm looking forward to seeing what everyone submitted!
  17. Replies
    6
    Views
    714

    Regardles of the board, you are going to want to...

    Regardles of the board, you are going to want to shorten up those bare ends. As minimal as possible to make good contact. You most assuredly have or will have intermittent or terminal shorts with...
  18. Replies
    2
    Views
    566

    Very nice! I especially appreciate that pommel.

    Very nice! I especially appreciate that pommel.
  19. Replies
    15
    Views
    1,889

    what did you use to wire it up?

    what did you use to wire it up?
  20. Replies
    6
    Views
    748

    Entropy!

    Entropy!
  21. Replies
    9
    Views
    1,663

    You are better off running your blade at around...

    You are better off running your blade at around 80-90% brightness from the start. It will reduce the drain and improve the battery life significantly, and the brightness won't be affected that much...
  22. Replies
    9
    Views
    1,663

    Unless you are using a matched pair of batteries...

    Unless you are using a matched pair of batteries or a battery pack it is not a good plan to wire lithium cells in parallel.
  23. Thread: Ianthe build

    by jbkuma
    Replies
    9
    Views
    1,407

    you can think of it kind of like ripping a DVD...

    you can think of it kind of like ripping a DVD and posting it to YouTube.
  24. Replies
    5
    Views
    737

    What battery and LED setup are you trying to use?...

    What battery and LED setup are you trying to use?

    There isn't much that can be wrong with the speaker other than possibly shorting, but I wouldn't expect 3 speakers to all have that issue (or even...
  25. Replies
    2
    Views
    1,274

    Keep in mind the LED gets very hot. I've built...

    Keep in mind the LED gets very hot. I've built several prototypes of this type of thing (see Space Windu's interview with me or a demo). My main concern with this as a product is that LEDs can get...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4