Search:

Type: Posts; User: kingcobra5352

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    2,493

    Wiring it with the blade would be cool! I usually...

    Wiring it with the blade would be cool! I usually follow this wiring guide the only difference being that the power indicator and the switch are one piece. Would I just connect the second LED to the...
  2. Replies
    5
    Views
    2,493

    Two accent LEDs on NBv3/4

    Currently I have an illuminated switch on my saber but would like to add something like this as well. Is that possible with the NBv3/4?
  3. Replies
    4
    Views
    2,392

    Using the nano biscotte v4. I was always told to...

    Using the nano biscotte v4. I was always told to round up the voltage of the power source since a full charge 3.7v battery is closer to 4v. Is that not correct?
  4. Replies
    4
    Views
    2,392

    Resistor Question

    So I'm doing a build with a RRW tri cree LED. If my calculations are correct I need a 1.5ohm 1.5w resistor for the reds but the only one the shop has are 1.5ohm 5w. I know these should work but they...
  5. Replies
    11
    Views
    19,109

    Is adding heat shrink to the bare wire an option?...

    Is adding heat shrink to the bare wire an option? I'm always worried that I'm going to melt the outside of the wire.
  6. Replies
    11
    Views
    19,109

    I have a shipment of speakers on the way that...

    I have a shipment of speakers on the way that should be here tomorrow. If resoldering this speaker doesn't work, I will try a new one. Just seems kind of weird for a brand new speaker to die in less...
  7. Replies
    11
    Views
    19,109

    I pulled the wires away and tried it. Still the...

    I pulled the wires away and tried it. Still the same issue.
  8. Replies
    11
    Views
    19,109

    I appreciate your reply. When you say the amp...

    I appreciate your reply. When you say the amp could be going, what would cause that?

    Someone else pointed out that my solder points on the board could be too exposed. Though, when I take out the...
  9. Replies
    11
    Views
    19,109

    Extreme Static on 2w 28mm speaker

    I recently completed my first build with a NBv4 in an Epoch saber. Everything was going fine for a few days after I worked out some bugs until the speaker started freaking out this morning.
    ...
  10. First Saber Build Issue

    I have finally built my first saber using a Saberforge Epoch and nano biscotte v4. The saber works if I swing it around but as soon as I duel with it, it acts up. I followed this wiring diagram. The...
  11. Replies
    3
    Views
    2,022

    I knew the LED posts mattered but I wasn't sure...

    I knew the LED posts mattered but I wasn't sure on the switch posts. I appreciate your help.
  12. Replies
    3
    Views
    2,022

    Momentary AV Switch Question

    I know that on a regular switch without an LED, it doesn't matter which post you use for positive or negative. Is this also true for the switch posts on an AV switch?
  13. Replies
    4
    Views
    2,649

    That makes sense. Thank you for the help.

    That makes sense. Thank you for the help.
  14. Replies
    4
    Views
    2,649

    Stupid LED question.

    I got a GGW TRI Cree LED for my first build. How do I know which LED is the white one? And for in the future for color mixing, how would I know which LED is which color?
  15. Replies
    4
    Views
    2,132

    You nailed it. I don't want to dive into it and...

    You nailed it. I don't want to dive into it and short out an expensive NBv3 board.
  16. Replies
    4
    Views
    2,132

    Modular installation

    Hello there. This is my first time looking into doing my own installation but I know nothing about soldering and wiring components. It it possible to do a NBv3 install with 100% modular/prewired...
Results 1 to 16 of 16