Search:

Type: Posts; User: jbkuma

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    2
    Views
    106

    I like it.

    I like it.
  2. Replies
    2
    Views
    179

    Your example 14500 will have approximately 7.8Wh...

    Your example 14500 will have approximately 7.8Wh (volts * amp hours = watt hours) while the 18650 will be 11.5Wh. The 18650 has more power available.

    The LEDs will not be brighter unless you plan...
  3. Replies
    1
    Views
    182

    What board are you using, the pixels only do what...

    What board are you using, the pixels only do what they are told.
  4. Replies
    9
    Views
    371

    Best way to learn is to have a project you really...

    Best way to learn is to have a project you really want to do and just do it.
  5. I have no idea but you can go to a hardware store...

    I have no idea but you can go to a hardware store and try things from the bins.
  6. Replies
    9
    Views
    371

    https://i.imgur.com/27RTKfS.jpg Illustrator...

    https://i.imgur.com/27RTKfS.jpg
    Illustrator Saber Club! I did make this one. Pick one and do it!
  7. Replies
    20
    Views
    850

    You do not understand what you are talking about....

    You do not understand what you are talking about. I am very aware of all of these things. You will likely not see a problem right away, and take this as confirmation that you were right, since you...
  8. If it is supported at both ends it should be...

    If it is supported at both ends it should be fine. How do you plan to secure the chassis?
  9. Replies
    20
    Views
    850

    The load needs to be disconnected so the charger...

    The load needs to be disconnected so the charger can detect the state of the battery. If you have a load drawing off the circuit while it's charging you risk damaging the battery by either over...
  10. Replies
    20
    Views
    850

    This is only meant as a charger, not to support a...

    This is only meant as a charger, not to support a load of any kind. To use this you would disconnect the battery from your project and connect it to this charger.
  11. Replies
    20
    Views
    850

    Which charger are you looking at?

    Which charger are you looking at?
  12. Replies
    20
    Views
    850

    An in-hilt will draw anywhere from 1-5A and a...

    An in-hilt will draw anywhere from 1-5A and a pixel blade will be about 3-8A for a 120x2 pixel blade typically. Longer pixel blades and different configurations will provide different results.

    I...
  13. Replies
    20
    Views
    850

    You want your battery disconnected from...

    You want your battery disconnected from everything else when you are charging, that is why many use a charge port. There are USB chargers that have built in load pads, but those are usually limited...
  14. Replies
    9
    Views
    445

    This is not correct. Panasonic makes the cell...

    This is not correct.

    Panasonic makes the cell itself, but the protection circuit is a point of interest. You can have a cell capable outputting 20A but have it capped at 1A by the protection. ...
  15. Replies
    9
    Views
    445

    Are you still getting sound, or does it just...

    Are you still getting sound, or does it just crash dead?

    Traditionally most 18650s have been protected at 3-5amps which is not sufficient for the pixel blade. It may or may not be related to the...
  16. Replies
    20
    Views
    1,476

    It looks great so far. I think my only real...

    It looks great so far.

    I think my only real complaint would be that the previews are a bit hard to see. If the back ground was white or black it might be easier to tell what the parts are. ...
  17. Thread: MHS Builder

    by jbkuma
    Replies
    4
    Views
    323

    The correct link is at the top of the forum,...

    The correct link is at the top of the forum, http://forums.thecustomsabershop.com/mhsbuilder/mhsbuilder.php?tabid=38
  18. Replies
    2
    Views
    286

    It's possible, but very tight. Your speaker will...

    It's possible, but very tight. Your speaker will likely be very close to the bottom, so you will probably need to use a tactile button rather than an AV that requires a lot of room. You might also...
  19. Replies
    6
    Views
    346

    All lithium cells should be charged before use.

    All lithium cells should be charged before use.
  20. Replies
    6
    Views
    346

    Without seeing photos it's hard to guess, but it...

    Without seeing photos it's hard to guess, but it could be a short circuit.
  21. Replies
    5
    Views
    421

    One of the 15A batteries. The protection circuit...

    One of the 15A batteries. The protection circuit is kicking in for over current on your battery.
  22. Thread: Crystals...

    by jbkuma
    Replies
    29
    Views
    3,271

    The problem with a cut and polished crystal is...

    The problem with a cut and polished crystal is that it won't capture the light.
  23. Replies
    5
    Views
    421

    Sounds like you have an inadequate battery.

    Sounds like you have an inadequate battery.
  24. No, it's meant to allow you to rotate the parts...

    No, it's meant to allow you to rotate the parts for alignment.
  25. Replies
    12
    Views
    757

    you can even get sheet aluminum. If you are...

    you can even get sheet aluminum.

    If you are doing just lettering you don't need to immerse the part. You are actually better off connecting the ground to your work piece and using an alligator...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4