Search:

Type: Posts; User: Arkhan

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds; generated 1 minute(s) ago.

  1. Poll: I have posted my Sith Hornet Reveal thread over...

    I have posted my Sith Hornet Reveal thread over at IRA
    http://imperialroyalarms.proboards.com/index.cgi?action=display&board=rk123&thread=636&page=1

    Take a look if you have time.
  2. The beauty of Tru-Color is that IA can pull his...

    The beauty of Tru-Color is that IA can pull his RGBW LedEngin, replace it with a RRRR and alter one or two of his config files for either RR + RR flash, or FULL POWERRRRR. No re-wiring necessary.
    ...
  3. She is a beauty. The paint job on the rear...

    She is a beauty. The paint job on the rear claw is excellent. Reminds me of fossils at the museum. If the Diatium power cell in the saber ever gives you, you can always beat people to death...
  4. Replies
    13
    Views
    9,045

    Poll: Congratulations to all the entrants. There...

    Congratulations to all the entrants.

    There were some excellent entries. Its alway nice to see what folks can do with MHS parts and a little ingenuity.

    Scintilla ends up winning a hard-fought...
  5. Poll: Congratulations to all the entrants. Special...

    Congratulations to all the entrants.

    Special congrats to IA for his year-long epic build for THE PURGE. Also congrats to Naigon for ensuring that my saber would sit in LAST PLACE out of three...
  6. Replies
    83
    Views
    15,126

    While I would have liked to have seen Scintilla...

    While I would have liked to have seen Scintilla with a higher-end audio board, it was the more ambitious design, IMO.

    I hear that the Igniter 2.0 + Tru-color had a very strong showing in the...
  7. Thread: Enough space???

    by Arkhan
    Replies
    7
    Views
    1,203

    The LED and optics holder sit INSIDE the base of...

    The LED and optics holder sit INSIDE the base of the bladeholder. The flange on the optics holder sits in the thread relief area of the choke. The heatsink then extends into the choke about .5"...
  8. Replies
    83
    Views
    15,126

    Placed my votes. Some really nice work in the...

    Placed my votes. Some really nice work in the MHS section. Too bad there weren't more entries in the custom sabers. I like to see the "unlimited" division entries.
  9. Replies
    83
    Views
    15,126

    I have sent an email to Lord Maul with the info...

    I have sent an email to Lord Maul with the info and photo links for my 2012 entry, May 29, 2012
  10. Replies
    11
    Views
    2,707

    Darth Odious: My thoughts exactly. Not only...

    Darth Odious:

    My thoughts exactly.

    Not only does a "proto-saber" allow for a very large battery solution, it also lets you use a MUCH larger speaker, properly enclosed.
  11. Replies
    148
    Views
    63,556

    Sticky: its hard to tell on camera of course but the...

    its hard to tell on camera of course but the "core" was safety-green, not white.

    You could see the thick walls but it was pretty much all the same color.
  12. Replies
    148
    Views
    63,556

    Sticky: At least with the "safety green" blade I had on...

    At least with the "safety green" blade I had on my Wormwood saber, it was a THICKWALL blade. As such, it very much had a center core.

    If you search here for "wormwood", you should find pics and...
  13. Replies
    23
    Views
    5,334

    I've been watching your progress on this one. ...

    I've been watching your progress on this one. The DEEP grooves and custom internal volume are top-notch. I was wondering just how you managed to cut rectangular shapes down the length of the main...
  14. Replies
    9
    Views
    2,181

    was I sick?

    was I sick?
  15. Replies
    9
    Views
    2,181

    Arkhan's Bell Stunt Saber

    I have a thread over on fx-sabers.com/forum on my now completed custom BELL stunt saber.


    No MHS in this one, but LED, resistors from TCSS.
    ...
  16. Replies
    9
    Views
    1,756

    180 degrees being "half a turn", you need to...

    180 degrees being "half a turn", you need to remove about .0275" from the end by sanding or other mechanical means
  17. Replies
    13
    Views
    2,389

    You need to take off .055" approximately to make...

    You need to take off .055" approximately to make a full 360 turn of the blade holder.

    All you need to do is figure out your approximate angle of "offness", divide that by 360 and then take that...
  18. Replies
    10
    Views
    3,001

    Slothfurnace was talking about the HASBRO FX...

    Slothfurnace was talking about the HASBRO FX board. The Hasbro FX board uses BATTERY+ and SPK- leads.

    If your board has SPK+ and SPK- leads, then you should use them.
  19. Thread: Sdf5

    by Arkhan
    Replies
    15
    Views
    3,830

    the finish washers are a great addition.

    the finish washers are a great addition.
  20. Replies
    33
    Views
    4,727

    brass, copper, black chrome

    brass, copper, black chrome
  21. Replies
    11
    Views
    11,180

    bh8 = blade holder #8 mhs gear = geared...

    bh8 = blade holder #8
    mhs gear = geared extension
    box 7 = well, box #7
  22. I remember a hilt that had an inflatable "blade" ...

    I remember a hilt that had an inflatable "blade" Not sure how old that one was, but it was "for the children"
  23. Replies
    12
    Views
    3,494

    Luxeon and Ledengin don't even LIST their Vr in...

    Luxeon and Ledengin don't even LIST their Vr in their technical specs. They both say "these LEDs are not designed for reverse bias operation"

    That means "please don't"

    Looking at some other...
  24. Replies
    12
    Views
    3,494

    Sure they can. You just have to PUSH harder. ...

    Sure they can. You just have to PUSH harder.

    There is a reason why most diodes list their reverse voltage.
  25. Replies
    12
    Views
    3,494

    The ones I got "show" that they are common...

    The ones I got "show" that they are common cathode, but they are in fact, common anode. I was aware of this when I ordered them.

    If I had wired the LED according to the silkscreen on the star, it...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4