Search:

Type: Posts; User: darth_chasm

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    195

    Nice! I didn't see that. That would definitely be...

    Nice! I didn't see that. That would definitely be better!
  2. Replies
    4
    Views
    195

    I believe the only one that locks in place is...

    I believe the only one that locks in place is this one but it is for MHS V1 https://www.thecustomsabershop.com/MHSv1-NeoPixel-Hilt-Side-Adapter-V2-P1341.aspx

    For the one you have you could do a...
  3. Replies
    3
    Views
    218

    Post high quality, close up photos of the board,...

    Post high quality, close up photos of the board, both top and bottom.

    Is your battery charged? Is your board secure from ambient vibration?
  4. no sweat

    no sweat
  5. I didnt read this whole thread so if this is out...

    I didnt read this whole thread so if this is out of place I apologize. But NB doesn't support the use of an Aux switch...
  6. Replies
    4
    Views
    332

    You need to find the specs of the led so that you...

    You need to find the specs of the led so that you can identify the forward voltage of the diodes. Then using that info, the battery voltage and ohms law you can determine your required resistance....
  7. I’m afraid I don’t live there anymore and I’m not...

    I’m afraid I don’t live there anymore and I’m not close. Otherwise I’d consider it.

    side note, Mark Hamill is filming there currently.
  8. Replies
    2
    Views
    2,521

    If you are referring to the longer, pre-wired...

    If you are referring to the longer, pre-wired "assembly" then no. It is not representative of all NB v4's. That is a custom board that was designed exclusively for TCSS. The differences between it...
  9. Replies
    3
    Views
    509

    Accent Pixel should do the trick. I personally...

    Accent Pixel should do the trick. I personally would wire it parallel to the blade. It's the diagram that appears above the one you posted here.
  10. Ha!! This is my hometown.

    Ha!! This is my hometown.
  11. Replies
    3
    Views
    662

    Welcome My gut tells me that if there is any...

    Welcome

    My gut tells me that if there is any change it will be negligible. Yeah, we use mirrored blade tips for in hilt leds but in that case the light is pointed directly at the reflective...
  12. Replies
    6
    Views
    772

    Thanks for the kind words guys!

    Thanks for the kind words guys!
  13. Replies
    3
    Views
    533

    Welcome back! Yeah, the hobby has changed quite a...

    Welcome back! Yeah, the hobby has changed quite a bit. Even in the time I've been active it has changed.

    CFX can run on 3.7v now without any hacks. You'll want to go with the high drain 15A cell....
  14. Replies
    6
    Views
    772

    Thanks SS. Long time no speak. Hope you're doing...

    Thanks SS. Long time no speak. Hope you're doing well.
  15. Replies
    1
    Views
    414

    you can charge one

    you can charge one
  16. Replies
    6
    Views
    604

    I think you might need to connect L3 to the...

    I think you might need to connect L3 to the Negative of the connector as well. I may be wrong so if someone knows otherwise please chime in. Also, did you order it set up for neopixel? There's a...
  17. Replies
    6
    Views
    772

    DCLS-006le #1

    I'm sure many have seen it already elsewhere, but TCSS was key in getting this done so I need to post this here as well. This is the refinement of the prototype design from a couple of years ago.
    ...
  18. Replies
    7
    Views
    1,135

    I've used 6-32 before that have worked ok for...

    I've used 6-32 before that have worked ok for light sword play. IDK, maybe others can chime in on the 4-40. It's just that the nose on those has such a small point of contact.
  19. MHS discs have 2 holes because thats what works...

    MHS discs have 2 holes because thats what works with MHS parts and MHS parts are not the same dimensions as a Graflex. So there is really nothing there making things complicated.

    Have you, by...
  20. Replies
    7
    Views
    1,135

    Personal preference, I wouldn't use 4-40. Im no...

    Personal preference, I wouldn't use 4-40. Im no engineer so I don't even know where to begin to determine if it is indeed too small. I just wouldn't.

    What kind of use is the saber intended for?...
  21. Replies
    4
    Views
    617

    It can happen and I can say with 98% confidence...

    It can happen and I can say with 98% confidence it's the blade that is slightly out of spec. Simply sand the 2 or so inches of the bottom of the blade. Plug up the end with some paper or cotton to...
  22. That looks really good!

    That looks really good!
  23. Replies
    2
    Views
    449

    Welcome to the addiction :D

    Welcome to the addiction :D
  24. These all incorporate custom chambers with a mix...

    These all incorporate custom chambers with a mix of 3D and other things. All is original though. No pre made stuff...
  25. Replies
    11
    Views
    1,525

    Congrats. Good job. Looks better than a lot of...

    Congrats. Good job. Looks better than a lot of other firsts, or thirds, or twentieths.

    Now the question is how soon until you make another :p
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4