Search:

Type: Posts; User: Jay-mo

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    31
    Views
    73,146

    I will be ordering a sinktube blade holder and...

    I will be ordering a sinktube blade holder and hopefully confirm it will act as a conversion kit until one is up or a better guide is around.

    EDIT: Input for those taking it apart, I did have to...
  2. Thank you everyone so much and special thanks to...

    Thank you everyone so much and special thanks to @acerocket for confirmation on the OD of the part!

    It should fit the 1.21" Mace Hilt quite nicely!

    Edit/Update: Still waiting on that check...
  3. @Vereous, Im asking if anyone knows the outter...

    @Vereous, Im asking if anyone knows the outter dimentions of a blade holder or kit that could fit into this saber. Its a mace windu 07' Hasbro Signature Series with a 1.21" ID
  4. 1.21" OD Blade Holder Ideas: Time to get creative!

    Hello all, if you have seen my thread in mr/fx signle led conversions youd know my project at the moment is a mace windu signature series by hasbro.

    Now, this saber is like joe jedi/kyberlight...
  5. Replies
    2
    Views
    16,502

    Mace Signature Series / Kit options

    Hey guys! Today I have a Mace Windu Signature Series on my table, totally disassembled. Quite different than the guides version, as in the guide the thin part of the conversion kit goes almost into...
  6. Replies
    47
    Views
    78,624

    Sticky: In a bad way, I take it? Either way- a good...

    In a bad way, I take it? Either way- a good reason to find a solution to the new 3 pronged sensor.

    When I unboxed my Rey/Graflex & twirled it around (for.. ahem.. testing purposes) for a little...
  7. Replies
    47
    Views
    78,624

    Sticky: So I've done a bit of research and feel like I...

    So I've done a bit of research and feel like I can now ask a few questions about this specific board (From Rey's/Graflex Blade Builder).

    1. The Swing Sensor has a ground. If I wanted to go for...
  8. Replies
    5
    Views
    4,715

    EDIT: I forgot to note the thread date,...

    EDIT: I forgot to note the thread date, unintentional thread necro'd this. Figure advice can't hurt.

    I'd love to add my input here- I've been etching a lot since I started this addiction/hobby.
    ...
  9. Replies
    391
    Views
    284,688

    Phenomenal thread! This has helped me so much...

    Phenomenal thread! This has helped me so much with older sound cards.

    Currently trying to figure out how to add a recharge port to this setup with an 18650- lots of research... With p
    lenty more...
  10. Replies
    2
    Views
    3,049

    Thread Necro card Played! Kidding, this did...

    Thread Necro card Played!

    Kidding, this did actually help me a lot, there is quite a few different boards out there. Any luck finishing with this one? I've gotten mine to power blue cree's without...
  11. Check out cutaway builds on the forum, too! I am...

    Check out cutaway builds on the forum, too! I am also working with my first two soundboards from Hasbro. Its fun stuff, I bought two at a used toy shop just in case one goes.. erm.. bad. I too am on...
  12. Replies
    1
    Views
    1,686

    You just won the best parent on the block award!...

    You just won the best parent on the block award! Well done! I'm still to scared to duel with the younglings in my family with the thick-walled blades. Has it seen some combat yet? :cool:
  13. Replies
    4
    Views
    4,463

    I've installed my own JST connectors- they're a...

    I've installed my own JST connectors- they're a pain. I found it very helpful to heatshrink the back of them once they were set in place/after testing a good connection.
  14. Replies
    11
    Views
    5,837

    EDIT @: Best bet would be a thin-walled blade, in...

    EDIT @: Best bet would be a thin-walled blade, in that case. They are still very strong and even glow brighter. I also hear that thick-walled is only for people who REALLY go all out in duels (So, my...
  15. Replies
    11
    Views
    5,837

    Unfortunately, your hilt will break before that...

    Unfortunately, your hilt will break before that blade ever will in an all out duel. My friend and I gave this a test after it was pointed out to me, in an all-out sparring match. I volunteered to use...
  16. I imagine thats the issue at hand: Storage. Do...

    I imagine thats the issue at hand: Storage. Do you know how many people would order if they could wait X amount of time for all parts to show up at the same time? A lot of people. I think Tim would...
  17. Replies
    11
    Views
    5,837

    I concur with most of the comments: 2" deep, 1"ID...

    I concur with most of the comments: 2" deep, 1"ID Blade Holder works great. Very durable. I've found the BRTS is best placed about half way in.

    I do, however, have a 1" deep blade holder on my...
  18. Replies
    3
    Views
    2,129

    I am new as well, and this is all a major...

    I am new as well, and this is all a major learning experience for new folks.

    Firstly, my personal advice for anyone getting into Saber Smithing: Expect parts to break, buy in sets of two if you...
  19. Replies
    6
    Views
    3,386

    Firstly, nice English! I'd like to comment on...

    Firstly, nice English! I'd like to comment on this, as quite a few people around have asked for improvised blade mirrors/etc. It may be helpful if we manage a good method of achieving this, though...
  20. Replies
    7
    Views
    3,902

    That will be a very heavy blade if you choose...

    That will be a very heavy blade if you choose that route.

    I always viewed the photon tips as more of an display piece for a display blade. They're beautiful, they will look great, but If I'd like...
  21. Thread: Blade ideas

    by Jay-mo
    Replies
    4
    Views
    2,877

    Welcome! I made my first two (still in "beta",...

    Welcome! I made my first two (still in "beta", working on carving and shaping the aluminum more) with 1"OD thick-walled blades. From what I have gathered, they aren't warranted unless its for...
  22. Thread: Batteries Li-on

    by Jay-mo
    Replies
    6
    Views
    2,502

    I totally agree, its very important if your using...

    I totally agree, its very important if your using two LI-ions. "Mating" the pair, as I call it.. Always use the same brand for a "mated" pair.

    Charge each one at the same rate (I.E if your...
  23. Replies
    27
    Views
    10,276

    Oh I have- Love it. Gotta love the scene where he...

    Oh I have- Love it. Gotta love the scene where he catches the two guys with the sketchy shopping cart! Not many tv series I like either, currently only watching Orphan Black and waiting on The Wind...
  24. Replies
    2
    Views
    2,386

    The pommel will be tricky, as it appears to be a...

    The pommel will be tricky, as it appears to be a flat cap with a rounded off part extruding, and then you have about 6-8 Flaring edges- are those the grips your referring to?

    Based off the...
  25. Replies
    6
    Views
    3,594

    As someone who is still perfecting their PVC...

    As someone who is still perfecting their PVC carving, well done! I can't wait to finish my 2nd PVC hilt, hopefully it will look as nice as yours! I'm still using what I now call the "Test Hilt".. the...
Results 1 to 25 of 38
Page 1 of 2 1 2