Search:

Type: Posts; User: Madcow

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    2,605

    Video: Plecter Pixel Blade Construction

    https://youtu.be/20Lfh3B2SQ4

    Various parts in this video will be coming to the store soon.
  2. Replies
    1
    Views
    2,208

    Video: LS6 Crystal and Box Assembly

    Crystal chassis:
    https://youtu.be/a7zEYAuvGZc


    Control Box:
    https://youtu.be/pJyKSB8Nlo4
  3. Replies
    0
    Views
    1,415

    Video: NeoPixel PCB Wiring

    A quick rundown of how to wire the PCBs


    https://youtu.be/Bt-YkXnwt28
  4. Replies
    0
    Views
    1,494

    Video: 2w speaker and speaker mount

    For the perfect fit.

    https://youtu.be/MLhCloMy_JI
  5. Replies
    2
    Views
    2,816

    Video: 18650 Battery Holder tips

    With the v6 speaker holder

    https://youtu.be/oGdwJqifXqE
  6. Replies
    116
    Views
    31,945

    Possibly, I'll add it to the list. You can also...

    Possibly, I'll add it to the list. You can also get some good feedback vibration from the 2w speaker.
  7. Replies
    116
    Views
    31,945

    Definitely planning this already

    Definitely planning this already
  8. Replies
    1
    Views
    2,329

    I was recently sent this question... "Hey Rob,...

    I was recently sent this question...

    "Hey Rob, I was watching your videos and noticed on the "Pommels Inserts and Clips" you showed an insert with the recharge port in the pommel.
    Which speaker...
  9. Replies
    4
    Views
    1,356

    Quick glance - looks OK to me other than the...

    Quick glance - looks OK to me other than the aforementioned switch LED resistor.
    If you find the blue is not as bright as you expect - try the same .5 ohm resistor as you have on the green
  10. Replies
    2
    Views
    2,204

    Video: Even Blade Illumination

    New video outlining the basics of an evenly lit blade:
    https://youtu.be/5pKYeFxqENU
  11. Replies
    0
    Views
    1,941

    Video: RICE interface

    Showing how to use R.I.C.E with your Plecter Labs saber:

    https://youtu.be/yQG126pvhrI
  12. Replies
    4
    Views
    3,141

    Yes - you wire the FoC LEC (-) there, but if you...

    Yes - you wire the FoC LEC (-) there, but if you bridge those pads you'll need to place your resistor elsewhere on that circuit.
  13. Replies
    4
    Views
    1,811

    Whenever you change the volume of a sound file...

    Whenever you change the volume of a sound file you risk altering a number of things. Perhaps the zero crossings at the beginning and end of each file get altered. I would check those too.
  14. Replies
    3
    Views
    1,046

    I would run them in parallel off the same accent...

    I would run them in parallel off the same accent LED pad
  15. Replies
    5
    Views
    1,799

    Those claws I machined from 1/4" flat T6 aluminum

    Those claws I machined from 1/4" flat T6 aluminum
  16. Replies
    5
    Views
    2,834

    Video: CF8 Crystal Illumination

    Some have asked for this. It's a breakdown of how to wire in a RGB accent LED and use the CF8's features to light a crystal.

    The 5mm RGB accent LED will be available in the store soon.


    ...
  17. I did that here: https://youtu.be/H9moBORo47A ...

    I did that here:
    https://youtu.be/H9moBORo47A

    Works great.
  18. Replies
    2
    Views
    1,013

    LED 1 is the low side, LED 8 is the high/full...

    LED 1 is the low side, LED 8 is the high/full side.
  19. Replies
    35
    Views
    4,354

    It's also possible that if your soldering iron is...

    It's also possible that if your soldering iron is too hot, or if you heat the contact for too long... the LED becomes un-soldered inside the switch. That happened once to me.
  20. Replies
    1
    Views
    2,329

    Video: MPS pommels, inserts, and clips

    How to secure a pommel insert with the clip

    https://youtu.be/2nMjz-19HzA
  21. Replies
    116
    Views
    31,945

    Good ideas - thanks

    Good ideas - thanks
  22. Replies
    3
    Views
    804

    Here... at about 6:40 ...

    Here... at about 6:40

    https://youtu.be/XOWnNJE3dRA?list=PLBZx-DMVqx7druzwlBkXoZZhd30_0LXNS
  23. Agreed - a drill press can get a perfect hole and...

    Agreed - a drill press can get a perfect hole and then the tap will likely be straight as well.

    Use a punch to get a starting point for your drill bit to keep it from "walking" and not going in...
  24. Replies
    2
    Views
    615

    Simply use the accent LED pads as described in...

    Simply use the accent LED pads as described in the manual. There is a different setting in each of the files for idle, for lockup, and for during blade action (in the led.txt)
  25. Replies
    12
    Views
    1,944

    Premium speaker right? Try starting up the saber...

    Premium speaker right?
    Try starting up the saber then while it's running, gently press the black surface of the speaker and see if sound returns temporarily while you press. If it does it's a blown...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4