Search:

Type: Posts; User: jbkuma

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    214

    Thanks! It's been disassembled for months,...

    Thanks! It's been disassembled for months, pending a refit. I just haven't gotten around to making the new electronics for it!
  2. Replies
    6
    Views
    214

    It looks to me like you are driving full,off,off...

    It looks to me like you are driving full,off,off and full,full,off
  3. Replies
    5
    Views
    151

    I was talking about the blade.

    I was talking about the blade.
  4. Replies
    5
    Views
    151

    I'm not sure how this module is setup, but...

    I'm not sure how this module is setup, but usually + really goes directly to the battery, the + pad is usually to feed power to the board. The manual shows both wires going, but the power isn't...
  5. Replies
    2
    Views
    201

    Make sure you aren't including meta data

    Make sure you aren't including meta data
  6. Replies
    7
    Views
    1,677

    Welcome back! Plenty of us have projects that...

    Welcome back! Plenty of us have projects that have been on going for years without so many achievements. I look forward to seeing this develop.
  7. Replies
    10
    Views
    741

    You can mount the LED directly to the blade...

    You can mount the LED directly to the blade holder and count on that as the heat sink.
  8. Replies
    10
    Views
    741

    If there is any excess material on the heatsink...

    If there is any excess material on the heatsink trim it down. You can try drilling through the blade holder and into the blade. Since you don't have a lot of room, I'd use small screws as you can. ...
  9. Clever!

    Clever!
  10. Replies
    8
    Views
    1,051

    Probably too long and too close! I haven't had...

    Probably too long and too close! I haven't had much time to work on the concept much, it works well, but there are things I would like to do better, and make things even more versatile.

    Here's my...
  11. Replies
    6
    Views
    579

    The main thing is you don't want your speaker...

    The main thing is you don't want your speaker bouncing around, and ideally it would be held snugly and as far from the pommel cap as much as you can manage in this setup. The speaker will generally...
  12. My kind of saber! This is really unique and...

    My kind of saber! This is really unique and interesting!
  13. Thread: Auto shut-off

    by jbkuma
    Replies
    6
    Views
    457

    What time of blade is it? (high power LED?...

    What time of blade is it? (high power LED? pixel?)
    How long is the blade able to stay illuminated?
    What kind of battery is in it?
    What color blade? (solid R, G or B would be most efficient, mixed...
  14. Replies
    8
    Views
    1,051

    That is good to know, I will keep it in mind.

    That is good to know, I will keep it in mind.
  15. Replies
    4
    Views
    565

    The pommel itself is agnostic, the overall design...

    The pommel itself is agnostic, the overall design will determine how the saber presents itself.
  16. Replies
    2
    Views
    370

    All LEDs only illuminate in one direction but...

    All LEDs only illuminate in one direction but some switches might have circuitry to work in either direction I wouldn't expect that in a 12mm switch, since there is barely enough room for the LED and...
  17. Replies
    13
    Views
    1,409

    You don't need to go any further than your...

    You don't need to go any further than your kitchen for examples of the oil. Any pan with baked on black or brown oil is what you'll get. olive oil has a high content of things that will smoke and...
  18. Replies
    5
    Views
    585

    The resistor should be able to handle that...

    The resistor should be able to handle that current load. It sounds like something else is going on, it could be that your + and - are bridged on your LED and your LED is seeing full current from the...
  19. Replies
    8
    Views
    1,051

    The 7/8" tube does not fit inside the 1" tube,...

    The 7/8" tube does not fit inside the 1" tube, and the 3/4" tube doesn't fit inside the 7/8" tube. Even if it almost fit, any bend or dent would cause it to get stuck even if you couldn't quite see...
  20. Replies
    4
    Views
    967

    You might get a better response with a topic like...

    You might get a better response with a topic like "Replacement for broken dooku blade" Before clicking, my first thought was that you were trying to make a curved blade and that I didn't really...
  21. Replies
    8
    Views
    1,051

    7/8" won't fit. I have done this with a 3/4"...

    7/8" won't fit.

    I have done this with a 3/4" pixel blade that I call "pixel core." I've been working on the best way to diffuse things properly.
  22. Replies
    13
    Views
    1,409

    You can also look at videos by various prop...

    You can also look at videos by various prop makers on YouTube for specific ideas.
  23. Replies
    3
    Views
    503

    I should have a demo video of just such a thing...

    I should have a demo video of just such a thing next week.
  24. Thread: Double check

    by jbkuma
    Replies
    3
    Views
    1,078

    Unless you are doing something pretty...

    Unless you are doing something pretty interesting, the LED in the activation switch should only be 20ma, and you would only need a 1/8watt resistor (actual dissipation is about 0.01 - 0.04 watt,...
  25. Replies
    19
    Views
    2,192

    Yes you are missing quite a bit. You asked...

    Yes you are missing quite a bit. You asked questions about topics it seems you don't grasp very well and we are trying to provide informed answers.

    You want a focused beam to maintain it's...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4