Search:

Type: Posts; User: ishtob

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    16,472

    finding someone to anodize the inside instead of...

    finding someone to anodize the inside instead of doing a PC would solve your problem
  2. Replies
    1
    Views
    2,058

    You might want to consider using a 7.4V battery....

    You might want to consider using a 7.4V battery. Crossguard sabers will use a minimum of 3 LEDs, each requiring ~3v. Yes you could wire them in parallel to keep the voltage requirements under 3.7v,...
  3. what's the current you want to run your white on?...

    what's the current you want to run your white on? I am calculating 3.7ohm
  4. Replies
    11
    Views
    4,452

    try the cree XP-L , runs roughly at the same...

    try the cree XP-L , runs roughly at the same brightness as 2 rebel whites, and could be brighter if you want to extend it past 2000ma

    here's my Cree XP-L running at 2400ma in broad day light (my...
  5. Replies
    11
    Views
    4,951

    how much heat would be produced wiht a 6v...

    how much heat would be produced wiht a 6v regulator?
  6. Replies
    11
    Views
    4,951

    well.. my li-ion battery is a pack, and i go the...

    well.. my li-ion battery is a pack, and i go the charger for it too, just didn't want to have to get another changer.
  7. Replies
    11
    Views
    4,951

    what is the cap for?

    what is the cap for?
  8. Replies
    11
    Views
    4,951

    Voltage regulator and heat

    planning on using a 5v 1.5A voltage regulator for the economy sound board. My current setup is 7.2V li-ion battery pack. How much heat would be generated from this step down? should I bother with a...
  9. Thread: US2.5 Question

    by ishtob
    Replies
    42
    Views
    15,870

    im not sure if it will drive a buckpuck... it...

    im not sure if it will drive a buckpuck... it might not be designed for that amount of current
  10. Replies
    74
    Views
    32,576

    Form II: Makashi After Form I's proliferation...

    Form II: Makashi

    After Form I's proliferation as a saber combat technique, Form II or "Way of the Ysalamiri," came about as a means of lightsaber-to-lightsaber combat. It is described as being...
  11. Replies
    28
    Views
    11,360

    vadar conversion Q's

    how do i remove the little pin on th epoly carbonate blade?
    this one:
    http://www.thecustomsabershop.com/sabers/scripts/05vader/16.jpg
  12. Thread: Luxeon K2

    by ishtob
    Replies
    105
    Views
    44,183

    Luxeon K2

    I just recently heard of these Luxeon K2, which are supposably brighter and generates less heat, cant really find much informations on it and have no idea where to find retails that sells it, anyone...
  13. Replies
    17
    Views
    9,238

    hm... mine is only ike 2-3 inches into the hilt,...

    hm... mine is only ike 2-3 inches into the hilt, and the electronics kinda gets in the way of the luxeon + optics

    can you take some pics of its inside after u modify it? so that we can see how to...
  14. Replies
    17
    Views
    9,238

    use a small screw driver (the flat kind) and...

    use a small screw driver (the flat kind) and carefully, but firmly ply it out, be careful not to detach the metal cap from the plstic thing that is glued to the switch, because if you do, it would...
  15. Thread: Force User List

    by ishtob
    Replies
    94
    Views
    38,000

    Name: Andy Chang Age: 17 Occupation: High...

    Name: Andy Chang
    Age: 17
    Occupation: High school senior
    Location: Fremont California
    Alias: Hsi-An
    Force Affiliation: Jedi Lightsaber smith Apprentice


    *waves to suit_man* here!! high school...
  16. Replies
    2,349
    Views
    1,100,592

    Sticky: here's my sabers, and im proud to say that i got...

    here's my sabers, and im proud to say that i got most of the parts from the custom saber shop [:D]

    EL blade:
    http://i6.photobucket.com/albums/y222/icbob/saber-sam.jpg...
  17. Replies
    6
    Views
    5,305

    oooo..... oil... i see i see

    oooo..... oil... i see i see
  18. Replies
    6
    Views
    5,305

    proper way to use tap drills?

    i bought a couple of the EL blade holders from the custom saber shop, the roblem is that the aluminum seems to be harder then my tap drills, i've already broken 3 drills and ruining 1 of the holder....
  19. Thread: Force Fx Blades

    by ishtob
    Replies
    2
    Views
    4,006

    you can have custom saber shop do the conversion...

    you can have custom saber shop do the conversion then purchase one of those 1/8' walled polycarbonate tubes and a clear tip, you do need to look for a defuser yourself.

    this will make it many...
  20. Replies
    17
    Views
    9,238

    if you dont want to make a removable blade, the...

    if you dont want to make a removable blade, the easiest thing to do is cut off some of the defuser (about 2 in) and then stick you luxeon with it's optics into the balde it sef, you will have to...
  21. Replies
    17
    Views
    9,238

    i hav emodded a mace, there wasnt enough room to...

    i hav emodded a mace, there wasnt enough room to make a removable assembly unless i take otu the sound and clash board, but i didnt, mine is now modded with non-removable blade....
  22. Replies
    16
    Views
    7,206

    ou can resolder them, but it might be easier jsut...

    ou can resolder them, but it might be easier jsut to get another blade and not duel with it, keep the broken one to wack ppl with
Results 1 to 22 of 22