Search:

Type: Posts; User: Jay-gon Jinn

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds; generated 55 minute(s) ago.

  1. Replies
    6
    Views
    343

    That is definitely a work of art....especially...

    That is definitely a work of art....especially love the copper tubing and conduit in the crystal chamber.
  2. Replies
    4
    Views
    304

    The blade tubes used by ultrasabers have...

    The blade tubes used by ultrasabers have traditionally been slightly too large to fit in mhs blade sockets. They use a different supplier and the tolerances are slightly larger.
  3. Replies
    1
    Views
    380

    I'd say that's a no...those modules are pre-wired...

    I'd say that's a no...those modules are pre-wired MHS led modules and are designed to only fit in the MHSv1 parts.
  4. Replies
    19
    Views
    4,256

    In this picture you have your speaker wired to...

    In this picture you have your speaker wired to the battery input pads: https://i.imgur.com/5kMPFm8.jpg Putting the battery supply through the speaker pads is probably not good for the board.
  5. Replies
    5
    Views
    1,146

    My mistake...saw them in the 7/8" section, ...

    My mistake...saw them in the 7/8" section, figured Tim had some in the 1" sizes too. I can tell you from past experience that the white tips don't light up as well as the clear ones, unless you...
  6. Replies
    5
    Views
    1,146

    White blade tips can be found in the store in the...

    White blade tips can be found in the store in the blade supplies section.
  7. Michael Hudnell = Zook on the forums here, and...

    Michael Hudnell = Zook on the forums here, and CHEWBACCA over on the FX-Sabers forums.
  8. That's the ball bearings in the swing sensors and...

    That's the ball bearings in the swing sensors and is normal.
  9. Replies
    19
    Views
    28,919

    Sticky: It's a loose fit, but yes.

    It's a loose fit, but yes.
  10. Replies
    5
    Views
    1,536

    The RGB Tri-Rebel can still be used with the...

    The RGB Tri-Rebel can still be used with the stock battery pack, but you'll want to use a resistor on the red regardless of whether or not you use either of the other colors. Both of those might...
  11. Replies
    3
    Views
    1,044

    Yeah, people used to use the "Rainbow Vacuum...

    Yeah, people used to use the "Rainbow Vacuum Wands" back a few years ago to make curved hilts out of.
  12. Replies
    23
    Views
    6,753

    Actually, there is:...

    Actually, there is: http://www.thecustomsabershop.com/15-Sink-tube-LEDBlade-holder--P1048.aspx

    It is found in this section of the store:...
  13. Replies
    17
    Views
    3,915

    The 05 Mace Windu is also missing some.

    The 05 Mace Windu is also missing some.
  14. Replies
    3
    Views
    1,101

    Those boards do not have any clash effects for...

    Those boards do not have any clash effects for the blade.
  15. I'm aware of that, acmusic didn't say for sure...

    I'm aware of that, acmusic didn't say for sure if he was going to swap out the original soundboard or not. The stock FX boards won't run them.
  16. I would recommend using this topic to figure it...

    I would recommend using this topic to figure it out: http://forums.thecustomsabershop.com/showthread.php?17109-Tutorial-FJK-s-quot-Down-and-Dirty-quot-guide-to-Ohm-s-Law I will tell you that I...
  17. FYI, you'll destroy that prizm if you hook it up...

    FYI, you'll destroy that prizm if you hook it up to a 7.4v pack. It is designed to run on a 3.7v battery.
  18. Replies
    17
    Views
    3,915

    I still have the images for the HFX 2010 Anakin ...

    I still have the images for the HFX 2010 Anakin rots for the tutorial I posted. The images may still be working for now, but they will not after march. I will re-upload in them to imageshack account...
  19. Thread: Rules

    by Jay-gon Jinn
    Replies
    12
    Views
    1,967

    It may help to understand the rules of the forum...

    It may help to understand the rules of the forum better if you read all of the stickied posts in this section...there are separate topics for those rules. Some of then may be dated, but might still...
  20. A stereo audio jack will not be able to retain...

    A stereo audio jack will not be able to retain the scrolling/extension and retraction effect he's looking to keep. The led 's in the blade are made in 6 serial segments, and each segment is wired...
  21. Replies
    7
    Views
    971

    give this a read, it may help you out, even...

    give this a read, it may help you out, even though some of the tech is old and out of date:
    http://forums.thecustomsabershop.com/showthread.php?3266-Jay-gon-s-PVC-Hilts-Full-tutorial-on-last-page
  22. Replies
    3
    Views
    1,053

    Actually, the sandpaper will remove the excess...

    Actually, the sandpaper will remove the excess material from the point of contact with the switch box, the center of the radius, and remove material until the sides of the curve fits flush. It...
  23. Black is the ground, red is board and speaker...

    Black is the ground, red is board and speaker positive, and brown is speaker negative. I am assuming it's the same as the older master replicas and hasbro models, though so I could be wrong.
  24. Replies
    3
    Views
    717

    If you're able, you could also just solder...

    If you're able, you could also just solder directly to the small resistor pad the trace leads to.
  25. I'll add that you do not need a lens holder with...

    I'll add that you do not need a lens holder with the tri Cree lens, it fits on the led star pad and is held in place when you screw in the heatsink. Also, the standard switch hole in the hilt will...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4