Search:

Ok so the fled and led parameters are for the main high powered led correct?

They have four numbers correlating to the four color channels on the board, do these also correlate to pads 5-8 because...

I think the color channels and accent pads make sense, let me know what I am goofing up.

Most crystal chambers would use a RGB led, and people love color changing so they run the LED to color...

I want the RGB LED to pulse red during the idle mode and I want it to turn green to mimic blade activation, then I want it to flash white when the main blade flashes white.

I have read that RGB...

Hello,

I have been reading through the CF7.5 manual and I found a couple of options for wiring a RGB 5mm LED.

I want the red to pulse when the board is in idle mode, then I want just the green...

Twin cree XPE photo reds, the warm white Cree XPE2 works just fine.

I just had someone on Facebook try and help but he just scared the snot out of me when he told me I can't add amps when calculating resistance.

I am verifying that some LEDs I have are bad, I am...

I read your tutorial and it's very helpful, I am just wanting to know that the same way you added the voltages of both die in series for calculating resistance, you treat amps the same way when...

Hello!

I trust this forum the most and I need to ask the good folks on here about Ohms law. I have been making sabers for a few months now and I may have a pretty massive flaw in my understanding...

I had it charging earlier today bit I wasn't sure one of the wires running to the board was solid so I re-soldered it and a few others.

Everything lights up properly on clashes, its very strange.

19650 3.7 li-ion 3400mah

I Will check the charge it should be good but I am not sure.

My nano should be wired correctly. I triple checked the wiring and even re-soldered the pads.

I have a battery, speaker, and tri cree (no flash on clash) as well as one accent LED running off the...

Thanks, it was worth a shot.

Dang, so close. Not worth messing with the hilt just to fit a hasbro cheap-o board.

Question: What are the dimensions of this board? Has there finally been a consensus on how many ohms the speaker is, on another thread I saw a guy say it was 8 and no resistor was needed.

I want...

Gotcha, thanks for the advice I was hoping deep sleep would stop all power drain but it's good to know a kill key will solve the problem, I can pop the charge port back in and be set to go, I just...

Ok so I have wired up a NB v1 to two blue LEDs in parallel (with resistors) and a 2W bass speaker. I am using a 18500 Li-ion to power it. Everything is wired with JST connectors

My problem is that...

Thanks I will also be reviewing all of the getting started threads on this forum and the youtube tutorials in detail before the build. Just to be double sure, you think I will be alright with those...

Thanks for all the info. So running two blues and a 2W speaker I can probably expect a half hour at best from a 1400mAh 3.7 battery, huh? I wimped out and went with the smaller battery for the...

Gotcha, I was hoping it was a solid feature. That's fine resistors it is then. So battery is 3.7 and forward voltage on the cree blues is 3.47 with 1A. So I should need a resistor that is .23Ohms and...

Gotcha, is this an error with just the V1 or V2 as well. I don't mean to question you Iam just used to thinking of manuals as bibles, but they might have written it not knowing that the drive...

Ok just for educational purposes, is the Nano Biscotte's drive parameter inferior or unsafe to rely on? I was reading the manual and running the calculations and the manual said that since my...

Hello all!

I am going to be doing a graflex build with a Nano Biscotte V1 to begin with so no flash on clash. I would still like to wire it to a tri cree and just wire the Blue/Blue LEDs and leave...