Search:

Good to know I'll try formatting it when I get home ty!

PS: The format worked Yay! Thanks all!

It will loop the poweron and power off sound or if I do clash and swing sounds they'll begin to loop

So I purchased the Resblade saber font and replaced my dark meat sound with it but the sound font starts to loop all the sounds. Is it because I didn't format the SD card before putting in the new...

Ok goodness I wish I was better at math, funny thing is I can do Chemistry (or use to) but anything else I'm just awful

Edit: oh that's in the store lol in my cart it goes

So I'm getting .29 and .29 which would mean 1 Ohm and 1 Watt is that right? Also I have the Trustfire 2400 going into this one that should be enough power right?

Oh I cant do math the other calculation I got was .29 ohms and 2.7 W

So if my calculations are correct I have a 3.7v battery and a Royal blue Cree meaning my resistor needs to be 3 ohms and 3W ?

3.7-2.7/1= 2.7 (3 Ohms)
2.7*1^2= 2.7 (3 Watts)

Any time I try to fit the 2W Bass speaker into the V4/V6 holder it doesn't seem to fit into the channel and just rests on top. I've tried the card/mat method that Rob shows in the vids but it always...

You don't need the buckpuck, and I'll let others give they're input

I've noticed when my saber gets low on power it'll play clash and swing sounds sporadically, so it's probably needing a charge

Nice! well built mate!

Lol SKS that's exactly what I did with my Speaker and the same pommel too! I'm curious how did you get it to prevent the wires from twisting?

That saber is Dope! how'd you fit all that in such a small ID?

If the accent ring LED is connected in parallel with the blade the switch will ignite with the blade correct? Or will it be on when power is brought to the hilt?

Yeah I was going to do a 28" or 26" blade in it my other hilt is about 15" long so it'll feel and look shorter. I'll be sure to adjust my list accordingly thanks SS

So I've finalized the design for my shoto...that is if you all think it'll work. (Ain't jumping the gun like last time ;) )
11031

I'm going for the removable battery/sound pack that is on the...

So I'm beginning to look into building a shorter off-hand saber. In doing so I think I have the design down to a rapier like saber (Almost akin to how the Sith Inquisitor wields his in Rebels) and I...

So after breaking the speaker twice :(, and redoing the chassis, getting real leather instead of fake cloth pleather I have completed my saber.

Meet "The Dark Imperator", owned by the once noble...

Sadly Craig that wouldn't have worked in my build because it's too tight, However I did use a piece of tubing to make a housing for the NB and works great.

My left speaker node broke off when i tried pull the heat shrink over the wires on the 28mm Premium speaker is there any way to repair it out do ihave to get a new one and hope it gets here before...

I have I wanted to be as budget efficient as possible, without going cheap obviously

So i got my Nano Biscotte and im trying to figure how is the best way to seat the sound board without it getting jostled, shorted or cherished inside of the hilt? I figured how to insulate and secure...

I'm so excited i have my electronics coming in tomorrow and ihave two days off next week to work on them. I've devised a plan to use thread screws to have the recharge port in the choke I'll be sure...

Alright so, If one has a latching switch and a NB (which don't work together obviously) how does one transform a latching to momentary or does one need to get a momentary?

Just in case you didn't get the notification the Nano Biscotte are back in stock