Search:

Type: Posts; User: RavenXp

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    19
    Views
    2,133

    Poll: I was raised on the pre-SE versions.

    I was raised on the pre-SE versions.
  2. Thread: NBV3 vs V4

    by RavenXp
    Replies
    16
    Views
    2,580

    It basically takes the (relatively) weak signal...

    It basically takes the (relatively) weak signal from that particular pad and amplifies it to where it can power a die on its own.

    I don't think it effects voltage, just gives the amperage needed...
  3. Replies
    14
    Views
    1,903

    Doing a neopixel build. Wanted plenty of mAh for...

    Doing a neopixel build. Wanted plenty of mAh for my saber. An 18650 would only last maybe 45 minutes per charge. Single cell at 3.7v, since the PRIZM can't handle voltage above 5v.
  4. Replies
    14
    Views
    1,903

    I always prefer the lithium packs. Although my...

    I always prefer the lithium packs. Although my current build I'm using 26650 batteries. Those things are huge.
  5. Replies
    19
    Views
    2,133

    Poll: I have the original trilogy before the SE...

    I have the original trilogy before the SE changes, but it's been a while so I can't remember it clearly.
  6. Replies
    2
    Views
    668

    Wait... Does that mean you copied the files then...

    Wait... Does that mean you copied the files then formatted? Eh, not gonna dig into you for it. We've all done things like that when we want to get our saber working.
  7. Replies
    5
    Views
    667

    If you have a multimeter, I'd test that channel...

    If you have a multimeter, I'd test that channel and see the voltage and amperage that's coming out of that channel.

    Edit: also, could you show me a shot if the back of the board, it looks like you...
  8. Replies
    7
    Views
    810

    I dunno, that shut down to be sounds like a short...

    I dunno, that shut down to be sounds like a short somewhere, not the resistors. Then again, I'll defer to the experts here.
  9. Replies
    5
    Views
    667

    Well, only other thing I could think of is...

    Well, only other thing I could think of is there's a component that's not working properly for that channel on the board. You did say you tried another LED that produced the same dim result with that...
  10. Replies
    5
    Views
    667

    Hm... You're sure the config for that die is set...

    Hm... You're sure the config for that die is set to full power, correct?
  11. Replies
    7
    Views
    1,059

    Hm, it's too bad I don't have any clear gift wrap...

    Hm, it's too bad I don't have any clear gift wrap to do that myself.
  12. Replies
    40
    Views
    19,982

    Sticky: Do you know yet how long the voting phase of the...

    Do you know yet how long the voting phase of the contest will be?
  13. Replies
    16
    Views
    1,692

    Well, it's just logic on my part. Most of the...

    Well, it's just logic on my part. Most of the crystal chambers I've seen are beautiful, but from the construction of them it doesn't *look* like they could hold up to dueling. But, I don't have first...
  14. Replies
    16
    Views
    1,692

    That's a very nice looking saber. The last couple...

    That's a very nice looking saber. The last couple I've made were battle type so I never really considered putting in a crystal chamber, afraid it'll break while dueling. Think the best saber I make...
  15. Replies
    2
    Views
    557

    From what I can tell it's probably rubber.

    From what I can tell it's probably rubber.
  16. Replies
    5
    Views
    3,120

    You could also try electro plating. You'd first...

    You could also try electro plating. You'd first need to electro plate the part in nickel, then brass. The down side is the brass plating uses some pretty harmful chemicals if you don't take proper...
  17. Kinda how I came across custom saber shop several...

    Kinda how I came across custom saber shop several years ago as well.
  18. Yeah, you'll have to adjust the sensitivity in...

    Yeah, you'll have to adjust the sensitivity in the config files. So many factors come into play for that sensor. Placement of the board in the hilt, vibrations from the speaker (can happen), etc....
  19. Replies
    10
    Views
    1,729

    You'd have to check the owners manual for that...

    You'd have to check the owners manual for that iron, they usually give a temp range that goes with those settings. But as its been said, it's best you get a really good soldering station with actual...
  20. Thread: speaker issues

    by RavenXp
    Replies
    3
    Views
    698

    I'd also like to add that depending on the...

    I'd also like to add that depending on the speaker type, the magnet could be cracked, but that's rare and I doubt it's probable. It's most likely what Don said.
  21. Replies
    4
    Views
    784

    My first saber I managed to find some cree LEDs...

    My first saber I managed to find some cree LEDs that were RGBW all in the center. But this was a couple years ago so not sure if they're still available. Think I did a search for 'Cree 1W RGB LED' or...
  22. Replies
    5
    Views
    911

    The wiring looks alright to me. The accent pads...

    The wiring looks alright to me. The accent pads look like they're going to a crystal chamber. If that's a RGB chamber you want to match the blade color it would be easier for color balance to wire it...
  23. Replies
    3
    Views
    608

    Um, what do you mean by bright order?

    Um, what do you mean by bright order?
  24. Replies
    2
    Views
    604

    That's odd. Is that with all your sound fonts or...

    That's odd. Is that with all your sound fonts or just one?
  25. Replies
    15
    Views
    1,861

    Very nice work. Makes me miss having access to a...

    Very nice work. Makes me miss having access to a machine shop. Wish these electronics were around when I was in high school, would've been able to machine out my own hilt and get school credit.
Results 1 to 25 of 114
Page 1 of 5 1 2 3 4