Search:

Type: Posts; User: LightsaberToothedTiger

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    1,887

    So still no luck after installing the high drain...

    So still no luck after installing the high drain battery. I’m convinced I’ve wired it all right. I’ll fiddle with the config a bit more. I’ll get it!
  2. Replies
    5
    Views
    1,887

    Thank you. I will keep you posted once I get a...

    Thank you. I will keep you posted once I get a chance to change the battery. Hoping I didnít damage my strips
  3. Replies
    5
    Views
    1,887

    Neopixel config issue?

    I managed to wire up a nano biscotte v4 to 2x ws2812b strips. 24 gauge wire on everything except the data line which is 30 gauge and 30 awg for the switch. Using a recharge port and currently hooked...
  4. Replies
    2
    Views
    1,263

    Smoking hot blue led no bs

    So not sure what the issue is. I have 1/2ohm 1/2 watt resistors on the blue diodes of the tri cree bbw wired to my nano v4. 1ohm 1watt on the white foc. I unbraided the multiconductor (local...
  5. Replies
    4
    Views
    2,008

    heh when it's a piece of art nothing is overkill...

    heh when it's a piece of art nothing is overkill :) I'm gonna go to the hardware store and pick some of this stuff up and see if I can smooth it up and get a bit more even overall. Thanks guys!
  6. Replies
    4
    Views
    2,008

    It's a nano biscotte v3. Sorry forgot to list....

    It's a nano biscotte v3. Sorry forgot to list. Yea I know it has a couple rough edges and it needs cleaning. Any other advice on clean up? I figured some very fine grit sand paper might work too?
  7. Replies
    4
    Views
    2,008

    Second lightsaber finished

    Hello all. I present Broken Heart. Because. specs are as follows

    Nano biscotte v3
    Blade holder 1
    Choke 2
    Hilt style 2
    Extension 3 with middle carved to give some character (courtesy of tim)...
  8. Replies
    9
    Views
    1,833

    I think jay was right. But it could have been a...

    I think jay was right. But it could have been a bridged pad I suppose. I think it was the positive wire running from the led module to the recharge port having a crappy connection. Everything works...
  9. Replies
    9
    Views
    1,833

    Just finished tediously cleaning all the pads and...

    Just finished tediously cleaning all the pads and making sure there's is absolutely no excess solder on/near pads. I really don't think bridged pads are the cause, 'due' to the fact that nothing has...
  10. Replies
    9
    Views
    1,833

    Workin on cleaning but still as I said in my...

    Workin on cleaning but still as I said in my first post: It works. Charges right up and everything. The leds just stay on constantly without activation the second you pull the kill key or recharger....
  11. Replies
    9
    Views
    1,833

    I tried going through and cleaning it up as best...

    I tried going through and cleaning it up as best I can. Still having the same issue though here's pics of it as is
    148691487014868
  12. Replies
    9
    Views
    1,833

    Issue with nano biscotte v3

    So wired it up and everything works as far as I can tell. However, my leds are on all the time. Even when I put the kill key in and refresh it, the two reds and the white are always on. Not sure what...
  13. Replies
    2
    Views
    1,127

    Awesome. I just used the dynaohm I had. May try...

    Awesome. I just used the dynaohm I had. May try different type in the future, so appreciated for that info.
  14. Replies
    2
    Views
    1,127

    Resistor Toss up

    So for a red accent with Vf 2.0 running with a current of 20 mAh using a 3.7 li ion with my NBv3, the dynaohm 20 mAh will be fine or do I have to acquire a 37/500watt 85ohm resistor or some similar?
  15. Replies
    5
    Views
    1,540

    Dope. So wire each positive pad of red and attach...

    Dope. So wire each positive pad of red and attach the resistor to each and then join the wires if desired/simplify things. Thanks dude!
  16. Replies
    5
    Views
    1,540

    I'm unsure about the set up for the wiring of...

    I'm unsure about the set up for the wiring of FoC. Do the two identical die have to be wired in series or can they be wired separately to the (+) pad with their own resistor?
  17. Replies
    5
    Views
    1,540

    Thank you so much, this is very good to know....

    Thank you so much, this is very good to know. Another way to save space if necessary.
  18. Replies
    5
    Views
    1,540

    Nano biscotte simple question

    So I have to be honest. My rgb "reyflex" build was powered by a igniter 2 soundboard. Umm that being said the wiring looks very similar but I'm a little confused. Are you not supposed to attach...
  19. Anyone in the Seattle area?

    Looking for some good mannered saber fights and I don't seem to know enough saber owners in my area. Can anyone help me solve this issue?
  20. Help with starkiller shroud designing please

    So im looking for opinions on this design idea. My starkiller build is consisting of Blade holder 2, 3.7 extension (didn't wanna try and line up screw holes on the v groove or ribbed so I went...
  21. That is art. A breathtaking masterpiece....

    That is art. A breathtaking masterpiece. Inspirational, dude!
  22. Thank you, good sir! Yea, you're right! I will...

    Thank you, good sir! Yea, you're right! I will hit up some shops and see if I can find something to mount up! But I will definitely buy a set of ears from tcss when I can. If I find something good...
  23. First MHS saber build completed!

    Hey. I'm a pretty big noob but here's my first MHS saber. I call it "Reyflex." I assume if Rey were to build a new saber or modify her current one it might look like this. Hope you guys like it....
  24. Methods for securing soundboards

    So I am still working on finishing my heavily modified KR black series and I'm wondering about alternative methods of securing a soundboard in the stock plastic case it comes with. If it comes to it,...
  25. Thank you very, very much FenixFire. I am...

    Thank you very, very much FenixFire. I am consulting the owners manual while editing my post. I should have been more clear that this is a Fx black series that I would like to make duel ready. And...
Results 1 to 25 of 26
Page 1 of 2 1 2