First time builder, just wanted someone to double check my parts list

Electronics
Proffie soundboard
Panasonic Li-Ion 18650 3.7V 3400mAh PCB Protected Rechargeable Battery
Switchcraft 2.1mm Power Jack
12mm Anti Vandal Momentary Red Ring Switch
Saber Essentials 28mm Stealth V2 Speaker
Pixel PCB Hilt side connector and 7 pins combo
recharge port kill plug style 6
switch, m5 momentary

Blade
sk6812 144 led neopixel strips x 2
foam tube
resistor, 330ohm smd 0603
1" Thick walled Trans White PolyC 40" long
Blade Tip
1" Thick Walled Pixel Blade Adapter

Crystal Chamber
5mm RGB LED

Hilt
MPS Pommel style 3 v2
MPS Clip
MPS Insert
MHS Extension Blank Style 1
5" Double female threaded connector
MHSv1 Blade Holder Style 4
Lube
Retention Screw

I think one of my friends has wire and shrink wrap so I didn't include it on the list. I'm also getting a 3d printed chassis so I didn't include it on my list.

In terms of tools I have a soldering iron, 3d printer helping hands, multimeter.

Is there anything else that I need or should get before building? Thanks!

Hey @the_senate ! Welcome to TheTCSSForum! Here's a couple of things that I could think of that you might need...

1. Resistors for your AV Switch's LED and 5mmRGB LED
2. A set of Wire Cutters/Strippers... https://www.digikey.com/en/products/...A70057/1850296 (You probably have these if you already have a soldering iron, but I thought it'd be a good reminder)
3. A Pair (or three) of Magnifying Glasses (3.50 Magnification) ... https://www.amazon.com/dp/B01IQCO1O4...ing=UTF8&psc=1
4. A set of Tweezers...
a. These are O.K. but need tweaking to get the tips perfectly aligned... https://www.digikey.com/en/products/...070001/5488233
b. These are very nice 316L Stainless Steel, but a bit short overall, and a little pricey... https://www.digikey.com/en/products/...-6-ITU/9664472
c. Basically the same as the above set, but a different stiffness (I can't tell the difference)... https://www.digikey.com/en/products/...-6-ITU/9664469
d. Same as 'b' but 304 Stainless Steel and 1/3 the price... https://www.digikey.com/en/products/...-B-ITE/9924689
e. Same as 'c' but 304 Stainless Steel and 1/3 the price... https://www.digikey.com/en/products/...-B-ITE/9664481
5. Isopropyl Alcohol and some Q-Tips to clean up your Flux after soldering. (You probably have these if you already have a soldering iron, but I thought it'd be a good reminder)
6. Battery Charger... https://www.thecustomsabershop.com/L...rgers-C86.aspx
I have this one, (Xtar VP2) but my battery/batteries is/are removeable... https://www.illumn.com/batteries-cha...v-charger.html

I hope this helps you a bit! Good Luck on your build!

Quote:

---

Originally Posted by the_senate

Electronics
Proffie soundboard
Panasonic Li-Ion 18650 3.7V 3400mAh PCB Protected Rechargeable Battery
Switchcraft 2.1mm Power Jack
12mm Anti Vandal Momentary Red Ring Switch
Saber Essentials 28mm Stealth V2 Speaker
Pixel PCB Hilt side connector and 7 pins combo
recharge port kill plug style 6
switch, m5 momentary

Blade
sk6812 144 led neopixel strips x 2
foam tube
resistor, 330ohm smd 0603
1" Thick walled Trans White PolyC 40" long
Blade Tip
1" Thick Walled Pixel Blade Adapter

Crystal Chamber
5mm RGB LED Since you have a neopixel blade, you can illuminate your crystal chamber with scrap neopixels from making your blade. It'll occupy less fets on your Proffie. A common anode RGB LED occupies 3 fets. Neopixel only 1.

Hilt
MPS Pommel style 3 v2
MPS Clip
MPS Insert
MHS Extension Blank Style 1
5" Double female threaded connector
MHSv1 Blade Holder Style 4
Lube
Retention Screw

I think one of my friends has wire and shrink wrap so I didn't include it on the list. I'm also getting a 3d printed chassis so I didn't include it on my list.

In terms of tools I have a soldering iron, 3d printer helping hands, multimeter.

Is there anything else that I need or should get before building? Thanks!

---

See my comments in red on your post. Good luck. Is this a MHS build?