No Recent Activity

26 Visitor Messages

  1. madmaxx
    View Conversation
    hey hey captain. i got my order on its way to sunny australia...it should be here by the end of the week....if i am lucky.I got everything else ready,assembled and right in my mind i think so this should be a fun build.I will put it into the comp if its completed but i might secret you some progress pics.anyway hope all is well talk to you soon
  2. madmaxx
    View Conversation
    arrr THAT contest...It would be nice but i doubt i would have it paided for or fully assembled by then....but you never know i guess.What about you capt? you got an entry in mind??
  3. madmaxx
    View Conversation
    and what contest is this?!
  4. madmaxx
    View Conversation
    have a look in my saber ideas folder. theres a pic of one of them. its tiny
  5. madmaxx
    View Conversation
    I went + spliced into speaker + and - into battery so the sound activates it with no resistor needed though the pcb.Its a 3volt pager motor. looks like a watch battery.its an enclosed unit.
  6. madmaxx
    View Conversation
    I picked up a few 3v pager motors. they work fine.i hot glued one to the inside wall of the hilt. little watch battery sized motor.
  7. madmaxx
    View Conversation
    nvm i tried it anyway. it sorta works
  8. madmaxx
    View Conversation
    heya captain.. do you know anything about rumble motors? specifically ..can i hook one up using the speaker output on a erm hmm novas..nd 3.0? and will the vibration mimic the sound ??
  9. madmaxx
    View Conversation
    hey capt.not sure if you remember me but i was looking at your crystal chamber pics for ideas a few weeks back.i have finished the saber with a much simpler chamber(manly cause i paniced at the difficulty lol) but it came out pretty good i guess. thanks for posting the pics though they were very helpful. cheers
  10. Boj-Vaati Mau
    View Conversation
    See if that'll work for you, sir.
    http://www.onlinemetals.com/merchant...=71&top_cat=60
Showing Visitor Messages 11 to 20 of 26
Page 2 of 3 FirstFirst 1 2 3 LastLast
Page 2 of 3 FirstFirst 1 2 3 LastLast
About captain_mills

Basic Information

About captain_mills
Country:
Wyoming
Occupation:
Professor of Mathematics & Physics
Zip Code:
82301
Interests:
Soccer, Volleyball, Track, Model Building, Sabersmithing (currently, lol), Camping, Hiking, Fishing

Signature




Remember, your LED will ALWAYS look brighter in pics and vids... If you're not playing with it at night, it's not gonna impress you...

Contact


This Page
http://forums.thecustomsabershop.com/member.php?7005-captain_mills&s=b1852bc9c613869dac640505046e6b4c
Instant Messaging

Send an Instant Message to captain_mills Using...

Statistics


Total Posts
Total Posts
167
Posts Per Day
0.03
Albums
Total Albums
6
Total Photos
71
Visitor Messages
Total Messages
26
Most Recent Message
10-06-2012 11:30 PM
General Information
Last Activity
01-13-2017 03:36 PM
Join Date
11-02-2010
Home Page
http://www.teachanddiscover.net

10 Friends

Showing Friends 1 to 10 of 10
View captain_mills's Blog

Recent Entries

PVC Rahm Kota Pt. II

by captain_mills on 09-21-2012 at 09:39 PM
2 Comments
So, I'm hoping I can get some help here, but since no one has seen my first blog post (or at least commented on it) I may have to post this into the Forums...

Anyway I am including a link to the Mace Windu board I am using in this saber. It has a tactile switch spot on the board and I can't figure out how to wire this switch to a momentary switch.

Anyone have any suggestions?

Thanks!

Read More

Updated 09-23-2012 at 09:13 PM by captain_mills

Categories
Uncategorized

PVC Rahm Kota

by captain_mills on 09-18-2012 at 08:47 PM
1 Comment
I decided to put together a Rahm Kota saber at a cheap cost. It'll be a variant. Somewhere between the one Rahm Kota had and what it became when Galen Marek used it... I'm using the one from the 'net I found as inspiration. It's made of 1" PVC for the main body, with an endcap and a coupling. The blade holder is also 1" pvc with a 3/4" grey PVC lathe-turned to fit inside. all the parts are lathed down in my wood lathe except the main body.

The electronics are from

Read More

Updated 09-19-2012 at 09:42 PM by captain_mills

Categories
Uncategorized

Crystal Chamber Pt. III

by captain_mills on 02-21-2011 at 10:09 PM
14 Comments
Ok, so I have an updated chamber that I'm going to put into my brother's Obi-Wan hilt that I posted in an earlier blog post. In part I, I showed off an incomplete version of what is below. This is the finished version, without the wiring, of course. I decided to put the original crystal back in it, and had to adjust it to get it to fit.

I will work on the wiring probably next weekend, since I will be busy the rest of this week (it was nice having Pres. Day off of work). There

Read More

Categories
Uncategorized

Crystal Chamber Pt. II

by captain_mills on 02-20-2011 at 06:59 PM
1 Comment
Hello again...

I spent the afternoon custom-making a crystal for the chamber. Took a piece of clear acrylic and put it to the grinding wheel. There's some "gunk" on the edges that I need to clean off (anyone know how to polish acrylic??). Otherwise, It's about 1 1/2" long and about 1/2" in diameter. It fits nicely into my chamber, and lights up nicely... Still not as bright as I'd like it to be though...

Album Image #1
Album Image #2

Read More

Updated 02-20-2011 at 07:01 PM by captain_mills

Categories
Uncategorized

Crystal Chamber & Saber Interior

by captain_mills on 02-19-2011 at 10:58 PM
1 Comment
So, today I decided to start work on the interior of my saber. There will have to be some adjustments, as I don't have my MHS saber parts yet, and have no idea exactly what the interior diameter will be on each of the parts. I consider this to be a trial run anyway, and I'm looking for suggestions and comments.

The LED is supposed to be green, but the way I have it wired, it's running off 4AAA's at 1.2V each (4.8V total) and with a 100 ohm resistor, it isn't bright enough to be

Read More

Categories
Uncategorized