View Profile: Jay-gon Jinn - The Custom Saber Shop Forums

Yesterday, 04:56 AM

Jay-gon Jinn replied to a thread Jay-gon's MHS ANI ROTS-ish in Gallery

Thanks guys, much appreciated!

5 replies | 106 view(s)

06-21-2017, 02:10 PM

Jay-gon Jinn replied to a thread CF8 LED + RICE Problem in LED hilts and wiring discussion

When you're using RICE to change your colors, are you clicking "store profile" before you click on "save override.txt"? That may help.

3 replies | 74 view(s)

06-21-2017, 02:06 PM

Jay-gon Jinn started a thread Jay-gon's MHS ANI ROTS-ish in Gallery

This is a saber that has been in the works, or planning stages for quite awhile for me. The project got started about 5 or 6 years ago when a friend...

5 replies | 106 view(s)

06-18-2017, 04:46 AM

Jay-gon Jinn replied to a thread Single LED Flash on Clash? in LED Questions & Answers

That's for adding another color to the FoC or setting the FoC to a specific color. The shimmering effect still applies to the main led as well. In...

4 replies | 143 view(s)

06-17-2017, 01:44 PM

Jay-gon Jinn replied to a thread MR FX sound modules schematics and discussions in Cutaway views and wiring schematics

No problem! Here's a visual reference for accent led wiring on these old boards: The green(neg) and white(pos) wires go to the led in an...

54 replies | 33697 view(s)

06-17-2017, 01:22 PM

Jay-gon Jinn replied to a thread Single LED Flash on Clash? in LED Questions & Answers

I believe all of the soundboards sold here at TCSS will be able to shimmer the led during FoC, so you will see an effect even with a single led. The...

4 replies | 143 view(s)

06-17-2017, 07:05 AM

Jay-gon Jinn replied to a thread MR FX sound modules schematics and discussions in Cutaway views and wiring schematics

Yes, you can use that switch, but you can also wire the led in the switch to come on when the blade is activated by wiring it in parallel with one...

54 replies | 33697 view(s)

06-16-2017, 01:14 PM

Jay-gon Jinn replied to a thread PLI Problem in LED hilts and wiring discussion

FYI, the soundboards sold in the store here, from PlecterLabs.com, are compatible with the MacOS. There can sometimes a few quirks with the...

5 replies | 155 view(s)

06-14-2017, 01:59 PM

Jay-gon Jinn replied to a thread Alternate shroud material that fits well over mhs hilt? in General hilt building

MHs parts were actually designed to fit inside a 1.5" chrome sink drain tube, so the fit is usually pretty good. Make sure you look for 22ga., not...

5 replies | 144 view(s)

05-31-2017, 06:54 AM

Jay-gon Jinn replied to a thread Wiring Issue or Fried Board? in General hilt building

The PIC on your board may be also damaged...you have a lot of solder and on that tiny little deep sleep pad your accent/switch led is wired to, and...

8 replies | 284 view(s)

05-31-2017, 06:50 AM

Jay-gon Jinn replied to a thread Chassis causing Hilt to Pommel Gap...need help in Modular hilt system

V4 speaker holder is this one: It is designed to fit inside the pommel, and as shown in Rob's video...if it isn't allowing your pommel to thread...

6 replies | 241 view(s)

05-29-2017, 09:18 AM

Jay-gon Jinn replied to a thread 18650 Battery Question in LED hilts and wiring discussion

There is only one Li-Ion cell sold at TCSS that is not protected, and it's this one:...

7 replies | 327 view(s)