Pullo
11-20-2009, 05:24 PM
Firstly this is my first tutorial so forgive any mistakes. :)
I wanted to build a Qui Gon jinn style saber but I still wanted it to have a smaller diameter handle, all of the other sabers I have built are sink tube and I came up with the following idea.
A 1.25 sink tube forms the base of this saber, cut to size, I compromised a little on the length of the saber to get a compatible looking diameter, my first attempt would have looked too "stocky". The overall length of the saber is about 11' 3/4". I cut the sink tube to size and drilled and tapped the 1.25 sink tube adapters to take the 8/32 round head bolts.
http://i649.photobucket.com/albums/uu220/lumeron/Image013.jpg
http://i649.photobucket.com/albums/uu220/lumeron/Image014.jpg
Next was to make an overlay to look like the ridges on the prop. I searched the internet but couldn't find a template so I marked out my own on a sheet of printer label that I had printed a grid on. I studied all the pictures of the prop I could find to copy a shape for the template. I then stuck this on a 1 1/2" black plastic waste pipe. This overlay would cover the sink tube but not overlap on the adapters at either end.
http://i649.photobucket.com/albums/uu220/lumeron/Image016.jpg
http://i649.photobucket.com/albums/uu220/lumeron/Image018.jpg
Added Blade holder 18, Pommel 7 and pommel insert 7, and sent them of to be powder coated. The switch is a black slide switch brought from my local electronic store (Sorry Tim !) this would be set between the top ridge of the handle, just below where the red thumbscrew would sit. both positions are marked in the photos above. The outer shroud was cut from a piece of 1 1/2"
aluminum pipe given to me by an ariel installer. I did have to grind down the interior of the pipe and the outside of the rear sink tube adapter to get it to fit but if you buy the aluminum sleeve that Time sells you won't need to do that. I downloaded a template from the inter-web and printed it again on to some sticky label then set about it with the dremmel. to remove the sticky paper after I had finished I soaked it for about half an hour in luke warm soapy water. Then sanded the shroud with a fine wet and dry and finally went over it with some metal polish.
http://i649.photobucket.com/albums/uu220/lumeron/Image010.jpg
http://i649.photobucket.com/albums/uu220/lumeron/Image008.jpg
With the main body back from the power coaters I cut a rectangle for the switch and drilled a hole to take the red thumbscrew, put the filed, sanded and finished overlay into place (the following pics don't show the plastic overlay in there finished state,) and then the thumbscrew holds it in place via a nut on the inside of the tube.
http://i649.photobucket.com/albums/uu220/lumeron/quibuild002.jpg
http://i649.photobucket.com/albums/uu220/lumeron/quibuild001.jpg
you can see where I had to grind down the sink tube adapter to fit the shroud, Electronics were added, sorry no pics, got a bit carried away and forgot to take any. You do have to remove the plastic shroud to solder the switch in place. Because of the inside diameter of the sink tube adapters being only 1 inch you can't fit a battery holder through them, this means I have to remove the whole adapter to change batteries a recharge port is Ideal, sadly i didn't have one, but I will probably upgrade later. My speaker is on the end of my Battery box and it doesn't sit inside the pommel. shame but i do need to remove it for the batteries. To assemble the main body, remove the rear adapter and slid down between the jaws of the shroud until the first ridge of the plastic overlay lies alongside the swept back curves of the shroud, when it is in place push the adapter back into place and add the securing bolts. I put two on top and one underneath through the covertec, which is why it is not in the correct place.
and that is it.
http://i649.photobucket.com/albums/uu220/lumeron/qui004.jpg
http://i649.photobucket.com/albums/uu220/lumeron/qui008.jpg
http://i649.photobucket.com/albums/uu220/lumeron/quibuild006.jpg
Hope this is of some use.
I wanted to build a Qui Gon jinn style saber but I still wanted it to have a smaller diameter handle, all of the other sabers I have built are sink tube and I came up with the following idea.
A 1.25 sink tube forms the base of this saber, cut to size, I compromised a little on the length of the saber to get a compatible looking diameter, my first attempt would have looked too "stocky". The overall length of the saber is about 11' 3/4". I cut the sink tube to size and drilled and tapped the 1.25 sink tube adapters to take the 8/32 round head bolts.
http://i649.photobucket.com/albums/uu220/lumeron/Image013.jpg
http://i649.photobucket.com/albums/uu220/lumeron/Image014.jpg
Next was to make an overlay to look like the ridges on the prop. I searched the internet but couldn't find a template so I marked out my own on a sheet of printer label that I had printed a grid on. I studied all the pictures of the prop I could find to copy a shape for the template. I then stuck this on a 1 1/2" black plastic waste pipe. This overlay would cover the sink tube but not overlap on the adapters at either end.
http://i649.photobucket.com/albums/uu220/lumeron/Image016.jpg
http://i649.photobucket.com/albums/uu220/lumeron/Image018.jpg
Added Blade holder 18, Pommel 7 and pommel insert 7, and sent them of to be powder coated. The switch is a black slide switch brought from my local electronic store (Sorry Tim !) this would be set between the top ridge of the handle, just below where the red thumbscrew would sit. both positions are marked in the photos above. The outer shroud was cut from a piece of 1 1/2"
aluminum pipe given to me by an ariel installer. I did have to grind down the interior of the pipe and the outside of the rear sink tube adapter to get it to fit but if you buy the aluminum sleeve that Time sells you won't need to do that. I downloaded a template from the inter-web and printed it again on to some sticky label then set about it with the dremmel. to remove the sticky paper after I had finished I soaked it for about half an hour in luke warm soapy water. Then sanded the shroud with a fine wet and dry and finally went over it with some metal polish.
http://i649.photobucket.com/albums/uu220/lumeron/Image010.jpg
http://i649.photobucket.com/albums/uu220/lumeron/Image008.jpg
With the main body back from the power coaters I cut a rectangle for the switch and drilled a hole to take the red thumbscrew, put the filed, sanded and finished overlay into place (the following pics don't show the plastic overlay in there finished state,) and then the thumbscrew holds it in place via a nut on the inside of the tube.
http://i649.photobucket.com/albums/uu220/lumeron/quibuild002.jpg
http://i649.photobucket.com/albums/uu220/lumeron/quibuild001.jpg
you can see where I had to grind down the sink tube adapter to fit the shroud, Electronics were added, sorry no pics, got a bit carried away and forgot to take any. You do have to remove the plastic shroud to solder the switch in place. Because of the inside diameter of the sink tube adapters being only 1 inch you can't fit a battery holder through them, this means I have to remove the whole adapter to change batteries a recharge port is Ideal, sadly i didn't have one, but I will probably upgrade later. My speaker is on the end of my Battery box and it doesn't sit inside the pommel. shame but i do need to remove it for the batteries. To assemble the main body, remove the rear adapter and slid down between the jaws of the shroud until the first ridge of the plastic overlay lies alongside the swept back curves of the shroud, when it is in place push the adapter back into place and add the securing bolts. I put two on top and one underneath through the covertec, which is why it is not in the correct place.
and that is it.
http://i649.photobucket.com/albums/uu220/lumeron/qui004.jpg
http://i649.photobucket.com/albums/uu220/lumeron/qui008.jpg
http://i649.photobucket.com/albums/uu220/lumeron/quibuild006.jpg
Hope this is of some use.