PDA

View Full Version : MHS LED holder



Reaper
03-16-2006, 08:18 PM
This might've been discussed at an earlier date and I just missed it, but after looking at the tutorials I'm confused: how does the led holder in the MHS hilt stay in? It seems like it's just sitting in there, but I don't think that can be the case.

xwingband
03-16-2006, 08:29 PM
The LED itself is held by nylon screws. The lens holder does "just sit there." There are four legs on the lens holder that lock it into the spokes of the star LED. It then is sandwiched between the blade holder and the heatsink.

Between the pictures and the cutout views here (http://www.thecustomsabershop.com/sabers/forum/topic.asp?TOPIC_ID=387) you should see how it works.

<center>http://www.geocities.com/ghost_soldiers_unit/gs_banner_trans2.gif
www.dewbackwing.com</center>

Reaper
03-16-2006, 08:47 PM
Thanks... yeah, I saw the pics, but I thought that there would need to be something else that held it firm for combat, but I see what you're talking about. Thanks again.

supertrogdor
03-17-2006, 11:32 AM
Reaper, i was also initially worried about this, but when you screw the blade holder to the hilt, it holds everything nice and tight so no worries

liongreek
07-21-2006, 07:13 AM
OK guys, dumb question I guess, reviving an old topic and all, but....I have completed the wirings and I am about to start putting the thing together. So my question is, how does the blade holder holds...the blade in place, especially for combat? Do I have to drill-n-screw it in place?

Again, pardon the ignorance masters...[;)]

BTW, Tim, the package...SUPERBLY DONE!!! Way better than I expected! Photos to follow soon!!

xwingband
07-21-2006, 07:42 AM
Yup, Drill and tap a thumbscrew to hold the blade in.

I'm adding this to the FAQ as I've seen it quite a bit lately.

<center>Read the FAQ (http://www.thecustomsabershop.com/sabers/forum/topic.asp?TOPIC_ID=552) or x-wing won't be happy. :(
Before posting did you check the Thread Index (http://www.thecustomsabershop.com/sabers/forum/topic.asp?TOPIC_ID=577)?.

http://img508.imageshack.us/img508/6703/xwing8az.gif</center>

liongreek
07-21-2006, 08:00 AM
Copy Red Leader...when you say drill, you mean the blade as well? So that the screw passes through the blade, or drill just the hilt to apply pressure on it?

Again, forgive my ignorance

Do-Clo
07-21-2006, 08:19 AM
Figure out where you want the thumb screw, preferred location is in the thicker part of the blade holder. Then remove your blade and drill and thread your hole, take a small file or sandpaper and smooth the inside of the blade holder where you drilled and tapped the hole and then insert blade and tighten thumb screw until the blade is snug and doesn't come out, don't use a wrench or pliers to tighten the thumb screw as you may damage your blade. The pressure of the screw pressing against the blade will hold the blade firm.

<center>http://i48.photobucket.com/albums/f217/Do-Clo/DoCloSig.jpg</center>
<center><font color="red"><font size="4"><font face="Comic Sans MS">Darth Technous Sith Lord</font id="Comic Sans MS"></font id="size4"></font id="red"></center>
<center><font color="red"><font size="4"><font face="Comic Sans MS">Give yourself to the Dark Side</font id="Comic Sans MS"></font id="size4"></font id="red"></center>

liongreek
07-21-2006, 10:46 AM
Thank you my Lord!!!

987654321a
07-21-2006, 11:42 AM
i had some problems putting together my mhs to 1.5" adaptor with my mhs blade holder, but no worries i got it together

I DONT KNOW WHAT WE'RE YELLING ABOUT!!....LOUD NOISES!!!
www.starwarscustoms.bravehost.com http://img430.imageshack.us/img430/9995/sithlord6jk8cr.png