PDA

View Full Version : 06 MR Obi Wan - Kits available



xwingband
06-12-2007, 08:05 PM
06 MR Obi-Wan Kenobi Conversion

This tutorial will show you how to convert your 2005 Master Replicas Obi-Wan Kenobi ROTS saber to a 3watt Luxeon using the conversion kit that I offer. The saber will retain all sound functions and use the original switch. You must make sure your hilt is the same design as the one shown in this tutorial. I make no guarantees that the wiring etc that I say to use in this tutorial will be the same in all models. You will need to have basic soldering and mechanical skills to do the conversion. You can reuse the stock MR blade by putting some clear or reflective tape around the base to make it a tad bit bigger. When finished you will have one very strong saber as everything between your hands and the PolyC blade will be metal to metal with no weak plastic.

Parts List
MR Obi Wan Saber
Conversion Kit (http://www.thecustomsabershop.com/MR-FX-Obi-Wan-ROTS-conversion-kit-P647.aspx)
8.7 Degree Collimator Lens (http://www.thecustomsabershop.com/Collimator-Lens-87-deg-viewing-angle-P537.aspx)
Lens Holder (http://www.thecustomsabershop.com/CreeRebel-Lens-Holder-P999.aspx)
Cree Star LED (http://www.thecustomsabershop.com/Cree-XP-E2-C136.aspx)
Thermal Tape (http://www.thecustomsabershop.com/Star-thermal-tape-pad-P483.aspx)

Optional but recommended
Complete 1" Blade to replace factory one (http://www.thecustomsabershop.com/Complete-Blades-C13.aspx)
8-32 screw for blade retention (http://www.thecustomsabershop.com/8-32-Thread-C43.aspx)
1/8" 8-32 set screw (optional - see end of tutorial for use) (http://www.thecustomsabershop.com/8-32-x-18-Set-screw-P108.aspx)


Picture of stock saber
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_01.jpghttp://www.thecustomsabershop.com/forum/images/Obi1/obiwan_02.jpg

Remove the battery pack and end cap.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_03.jpg

Pry off the gold strip, using a small screwdriver or X-Acto knife. Don't pry off the black part, just the thin gold strip.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_04.jpg

Take out the two screws holding on the control box. Pull off the box.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_05.jpg

Snip off the wires from the switch, and set the box aside. Push the switch leads into the hilt.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_06.jpg

Unscrew the emitter. You will need strap wrenches or something to get a good grip on the hilt. This can be very difficult to remove.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_07.jpg

There is a plastic ring on the inside of the emitter. Shave it down so that the blade holder fits correctly in it. The blade holder should sit flush with the inner lip now.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_08.jpg
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_09.jpg
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_10.jpg

There is a small pin on the threading of the emitter. Pound it through with a nail punch.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_11.jpg
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_12.jpg

Slid the electronics out through the pommel end. This can be VERY difficult.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_13.jpg

There are 3 pins in the electronics sled. The one closest to the blade gets pounded all the way through. The other two ones are small and only need to be pushed inside the housing, using a punch.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_14.jpg

Split apart the housing. You will get a bunch of plastic parts. Here they all are.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_15.jpg

Cut the wires from the LED strip. Cut them to ~1.5" long. Leave the gray wire alone.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_16.jpg

Strip and tin all the wires.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_17.jpg

Solder two leads onto the LED. Make sure your LED is oriented properly. Now is when you put the thermal tape on (not shown). It sticks between the LED and heatsink.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_18.jpg

Solder the other leads to the two you put on the LED. Blue wire on shock sensor connects to Positive terminal on LED
Purple wire from connector connects to Positive terminal on LED
Gray wire leave alone
Brown,Red,Orange,Yellow,Green, and Blue wire from connector connects to negative terminal of LED
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_19.jpg

Now is a good time to test out your saber!
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_20.jpg

Now, take the new blade holder, and line it up with the old plastic one. This picture shows a rough approximation of where it should be cut. If you cut it a little bit too short, then that is okay. Just get it close.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_21.jpg

Now take the heatsink and optics. Install the optics and thread the heatsink into the blade holder.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_22.jpg

Take the piece you cut from the original blade holder and slide it over the wires from the blade holder. Then plug in the connector to the sound board. Take the assembly together, as shown. Alignment doesn't matter, except for the slots on the two stock plastic parts, which should match up.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_23.jpg

Slide the electronics into the hilt, and pull the switch wires through.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_24.jpg

Resolder the switch to the switch leads.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_25.jpg

Install the control box, and glue on the gold strip. Hot glue will work fine here.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_26.jpg

Screw on the emitter. Make sure it is nice and tight.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_27.jpg

Drill and tap a hole for blade retention.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_28.jpg

Right now, the blade holder can spin if the retention screw is removed. To stop this, it is recommended to put a set screw in the threads, hidden by the emitter. Simply drill out the existing hole that you pushed a pin out of and thread it for an 8-32 screw. If you cut your plastic parts too short, then this screw will keep the blade holder from being pushed into the hilt. It is a nice little failsafe.
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_29.jpg

Deburr your holes and put the emitter back on. Insert batteries, and fire up the saber. You are done!
http://www.thecustomsabershop.com/forum/images/Obi1/obiwan_30.jpg