View Full Version : part(s) question...
http://www.thecustomsabershop.com/MHS-ribbed-extension-P245.aspx
1a.) the 'female' side of the ribbed extension.. how LONG is that 'un-ribbed' portion?
if anyone has one can they give me a quick measure??
1b.) are the ribbed extensions wide enough (ID) to house any/all electronics one would want/need? (sound board...speaker...etc..etc.)
also...
http://www.thecustomsabershop.com/Screw-on-LED-blade-holder-style-3--P184.aspx
blade holder #2
2a.) when the grooves/ribs stop (and before he threads start) there is a small section of how long is that section.. if anyone has one and can give me a quick measure.. Id appreciate it.
Im just to finalize my build/order (again), and the 'correct lengths are going to be vital on ordering and making the covers.
Thanks
Onli-Won Kanomi
03-18-2008, 03:51 PM
1a I just measured the "unribbed" female side portion on mine and it is slightly more than 21mm slightly less than 22mm [closer to 22mm]...thats on the outside which I assume by your question is what you are asking?
1b I know the inside will fit my Ultrasound v1 board...and I have read that the Ultra MLS light module will fit in it but I dont own one to check so I cant say if they would both fit at the same time nor do I own a CF to say whether those would fit...some of the rechargeable battery packs sold here say they will fit in it too as I recall.
hope this is some measure of help
BhujangiJedi
03-18-2008, 03:56 PM
I don't have calipers, so hopefully ruler & eyeball is precise enough - regarding question 2, just a hair over 15mm.
thank you both...
(not Im off to do a mm to inches conversion) lol
Atomic
03-18-2008, 07:00 PM
2a. Just bought that piece myself. The unthreaded section of the male end is just a bit over 1/8".
uh-oh..
ok.. now Im confused..
I was first told that blade holder #2
above the threads.. (so still the part that is roughly 1.45 in .in width still)
was a hair over 15mm
which is 0.5906 inches....no? meaning a little over a 1/5 inch?
the ther is 1.5 inches above that (ribbed/grooved still to the top?..correct?)
hmmmm
also.. for the RIBBED EXTENSION..
22mm = 0.8661 inches..right?
so almost 1 inch of non-ribbed section? and the totle length (not includeing threads of course..just added length to over-all hilt) is 3.7 inches? (minus this almost 1 in. of non-ribbed?.. so only 2.9 (roughly) of ribbed section on that whole piece??
is this correct?
thanks for the replies guys. appreciate it. :)
kiltedmikey
03-18-2008, 08:21 PM
0.5906 inches is close to 5/8" (19/32" is really close). So little under 1.5 of ribbed would be correct. 0.8661 inches is close to 7/8" (27/32" is really close). just guessing you were looking to grab you tape measure/ruler.
BhujangiJedi
03-19-2008, 12:02 AM
Too many words, not enough pictures.
To clarify:
http://forums.thecustomsabershop.com/attachment.php?attachmentid=135&d=1205910053
15 mm is 0.59 inches. 2.5 mm is close to 1/8 of an inch.
Powered by vBulletin® Version 4.2.3 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.