ti-el_terall
05-26-2007, 11:43 AM
Yep, I did. And I only had it for 24 hours.
Step 1. On the opposite side of the black know there is a pin. Drill it out. When kits are done it will be tapped with 8-32.
http://i45.photobucket.com/albums/f58/Ti-el_Terall/100_1046.jpg
Step 2. Unscrew the black knob. Take off plastic cover where the switch is. 2 screws are underneath and. Unscrew them, unscrew the big screw and take off control box.
http://i45.photobucket.com/albums/f58/Ti-el_Terall/100_1039.jpg
http://i45.photobucket.com/albums/f58/Ti-el_Terall/100_1042.jpg
Step 3. Slide black sleeve up to reveal a pin. Push it out.
http://i45.photobucket.com/albums/f58/Ti-el_Terall/100_1045.jpg
Step 4. Pull out innards.
http://i45.photobucket.com/albums/f58/Ti-el_Terall/100_1047.jpg
Step 5. Push out 2 small pins on opposite sides that keep the 2 pieces together.
http://i45.photobucket.com/albums/f58/Ti-el_Terall/100_1048.jpg
Step 6. Roll down O-ring on top of metal guard. Remove metal guard.
http://i45.photobucket.com/albums/f58/Ti-el_Terall/100_1049.jpg
Step 7. You should now see the end of another pin, flip saber over and push out pin.
http://i45.photobucket.com/albums/f58/Ti-el_Terall/100_1051.jpg
Now you can remove blade and such. Any questions please ask. I will make better pics eventually.
http://i45.photobucket.com/albums/f58/Ti-el_Terall/100_1053.jpg
Step 1. On the opposite side of the black know there is a pin. Drill it out. When kits are done it will be tapped with 8-32.
http://i45.photobucket.com/albums/f58/Ti-el_Terall/100_1046.jpg
Step 2. Unscrew the black knob. Take off plastic cover where the switch is. 2 screws are underneath and. Unscrew them, unscrew the big screw and take off control box.
http://i45.photobucket.com/albums/f58/Ti-el_Terall/100_1039.jpg
http://i45.photobucket.com/albums/f58/Ti-el_Terall/100_1042.jpg
Step 3. Slide black sleeve up to reveal a pin. Push it out.
http://i45.photobucket.com/albums/f58/Ti-el_Terall/100_1045.jpg
Step 4. Pull out innards.
http://i45.photobucket.com/albums/f58/Ti-el_Terall/100_1047.jpg
Step 5. Push out 2 small pins on opposite sides that keep the 2 pieces together.
http://i45.photobucket.com/albums/f58/Ti-el_Terall/100_1048.jpg
Step 6. Roll down O-ring on top of metal guard. Remove metal guard.
http://i45.photobucket.com/albums/f58/Ti-el_Terall/100_1049.jpg
Step 7. You should now see the end of another pin, flip saber over and push out pin.
http://i45.photobucket.com/albums/f58/Ti-el_Terall/100_1051.jpg
Now you can remove blade and such. Any questions please ask. I will make better pics eventually.
http://i45.photobucket.com/albums/f58/Ti-el_Terall/100_1053.jpg