PDA

View Full Version : El Lightsaber questions



obiwankenewbie
03-01-2007, 04:42 PM
Hey, i'd like to build a red bladed EL lightsaber and i've seen tons of plans online. One involved wrapping the wire around a metal pole that was put into the handle. another was just folded up or something. Could someone draw up or show me a picture of the best blade design? also i'd like to mount in some kind of sound board if possible, the cheaper the better. i read a little about hasbro sound boards, but still dont know how to wire them or mount them in the handle. Any wiring schematics you could give me would be greatly appreciated. Thanks! (also any info you can give a first time saber builder will be greatly appreciated)

Firebird21
03-01-2007, 04:50 PM
Take 2 and call me in the morning...


Thread Index (http://www.thecustomsabershop.com/forum/viewtopic.php?t=577)

Introduction to EL sabers (http://www.thecustomsabershop.com/forum/viewtopic.php?t=2167)




You may want to start here (http://www.thecustomsabershop.com/forum/viewtopic.php?t=2233)though... :wink:


P.S. I like the Screen Name. But I think there's another like it...

obiwankenewbie
03-01-2007, 05:06 PM
thanks for the pointers, i see the el fblasde setup and the wires are a lot closer than i expected, which is good. What diameter EL do i want?

also, what kind of tubing could i get? i hate to be a helpless noob, but i am. Could you give me links to the products page of what you use? i tried looking on mcmaster.com or something like that, but allt the choices confused me. :oops: Thanks for all your help! also, anyone know about the sound board? if not, no prob i'll figure something out.

Angelus Lupus
03-01-2007, 05:08 PM
Try the store that this forum is attatched to.
http://www.thecustomsabershop.com/default.aspx

obiwankenewbie
03-01-2007, 05:37 PM
alright i put together a list of obvious stuff i'll need, can anyone make sugggestions of what more i'll need?

obiwankenewbie
03-01-2007, 05:42 PM
forgot to add the list of items, sorry

PolyC Tube
SKU: 40PolyC $11.99
10-32 set screw
SKU: 10-32Set $0.20
HD polyethylene
SKU: PolyE $1.92
2.5mm High Bright Long Life - Red
SKU: 2.5mmHB-Red $14.00
1/4" Mono plug
SKU: M/plug $2.05
4Khz Inverter
SKU: 4KInverter $10.50
1/4" Mono Jack
SKU: M/Jack

obiwankenewbie
03-01-2007, 05:55 PM
changed it to 17' because i want a 40" blade, didnt realize i'd need that much.

xwingband
03-01-2007, 08:01 PM
Yup, that's to light it up... hilt stuff would be more, but I assume you have that thought out.

obiwankenewbie
03-02-2007, 09:14 PM
i think i know basically what i'll need for the handle: female jack, stereo wire, switch, metal pipe, any other doodads i want for the decoration of the handle. Anything else necessary?

Jedi-Loreen
03-02-2007, 09:53 PM
You'll need some sort of blade holder. There are ones in the store that you can mount into the 2 main diameters of sink tubes that people use, if you're going that way.

Ryma Mara
03-03-2007, 12:07 AM
An el blade holder, if your gonna go with MHS then you can use many different parts in the MHs center and misc section of the store.

If ya are gonna go with a sinktue your gonna need a MHs to sinktube adapter. if ya want an MHS pommel then your gonna need another MHS to sinktube adapter. but there is a sinktube pommel also in the sinktube and misc section of the store.

obiwankenewbie
03-03-2007, 10:24 AM
thanks!