coronhorn
02-07-2014, 10:31 PM
Basic info to get started I currently own three Ultrasaber sabers and I'm looking at retrofitting them with some updated electronics. I've been looking at different solutions and I wanna get some opinions on what I've come up with.
Saber #1 is one of their MHS compatible Consular models, I've got a Li-Ion setup in it with a 1000ma buck puck and one of their Obsidian 2.0 sound boards.
Sabers #2 & #3 are identical Aeon hilts which US labels are MHS compatible meaning you can change the pommels, both are running Li-ion setups with 1000ma Bucks.
I've had repeated breakage of the wiring on the battery packs in all three sabers and so I'd really like to get away from the current setup and move to something a little less prone to breakage what I was looking at buying was one of the MHS speaker mount V6 (http://www.thecustomsabershop.com/MHS-speaker-mount-V6-P892.aspx) mount kits. It says that it's designed for use with the NB sound board which is not a problem since that's the board I was looking to upgrade the two Aeon hilts with, mean time I figure I figure it the mount would work just fine sans speaker and NB to hold the upgraded batter packs in place in the hilt. The two real questions I had were these
#1 Will this battery pack Panasonic Li-Ion 18650 3.7V 3400mAh PCB Protected Rechargeable Battery (http://www.thecustomsabershop.com/Panasonic-Li-Ion-18650-37V-3400mAh-PCB-Protected-Rechargeable-Battery-P853.aspx) work with the above mentioned MHS speaker mount?
#2 I know the MHS speaker mount V6 (http://www.thecustomsabershop.com/MHS-speaker-mount-V6-P892.aspx) is designed with the NB in mind would it be at possible to squeeze the US Obsidian I have in Hilt #1 into the V6 mount and couple it with one of the above mentioned Panasonic Li-Ion packs, assuming that's the right one for use with this mounting kit?
I appreciate any and all advice or knowledge on the subject.
Saber #1 is one of their MHS compatible Consular models, I've got a Li-Ion setup in it with a 1000ma buck puck and one of their Obsidian 2.0 sound boards.
Sabers #2 & #3 are identical Aeon hilts which US labels are MHS compatible meaning you can change the pommels, both are running Li-ion setups with 1000ma Bucks.
I've had repeated breakage of the wiring on the battery packs in all three sabers and so I'd really like to get away from the current setup and move to something a little less prone to breakage what I was looking at buying was one of the MHS speaker mount V6 (http://www.thecustomsabershop.com/MHS-speaker-mount-V6-P892.aspx) mount kits. It says that it's designed for use with the NB sound board which is not a problem since that's the board I was looking to upgrade the two Aeon hilts with, mean time I figure I figure it the mount would work just fine sans speaker and NB to hold the upgraded batter packs in place in the hilt. The two real questions I had were these
#1 Will this battery pack Panasonic Li-Ion 18650 3.7V 3400mAh PCB Protected Rechargeable Battery (http://www.thecustomsabershop.com/Panasonic-Li-Ion-18650-37V-3400mAh-PCB-Protected-Rechargeable-Battery-P853.aspx) work with the above mentioned MHS speaker mount?
#2 I know the MHS speaker mount V6 (http://www.thecustomsabershop.com/MHS-speaker-mount-V6-P892.aspx) is designed with the NB in mind would it be at possible to squeeze the US Obsidian I have in Hilt #1 into the V6 mount and couple it with one of the above mentioned Panasonic Li-Ion packs, assuming that's the right one for use with this mounting kit?
I appreciate any and all advice or knowledge on the subject.