PDA

View Full Version : Lord Zen's first saber



Lord Zen
05-26-2013, 10:56 AM
Hi everyone,
This is my first post and over the next series of posts I hope to detail a retrospective build log of my first lightsaber.
Hopefully some people will find these posts interesting or informative.

The project was completed in early January, but only now do I have the time to do the write-ups.

Before starting this project I spent a number of weeks reading over the numerous helpful and inspiring posts by the lightsaber building community.
I am indebted to all those who have taken the time to selflessly share their insight and wisdom with others.
I am also grateful to those who offer their skills and services to provide the products and technologies that allow our lightsabers to become a reality.

Over the period of building this saber I learnt much, made mistakes, swore a little, read and re-read guides, burnt my finger once, and became totally engaged in this little project.

I'm afraid this first post will only be text, but I will include "in-progress" pictures later

So for now, listed below, is what was included in my shopping order:

• 1 of: White shouldered 1" thick walled blade tip with reflective disc
• 1 of: 1" Thick walled Trans White PolyC 40" long (30 inches)
• 1 of: Collimator Lens 5 deg viewing angle
• 1 of: LEDengin Lens Holder
• 1 of: LED Engin LZ4 10W Multi Color (RGBW)
• 1 of: Star thermal tape pad
• 1 of: MHS "new style" Heat Sink V2
• 1 of: 3.7V-14.8V Li-Ion Smart charger
• 1 of: 2.1mm Power Jack
• 1 of: 2.1mm Power plug
• 1 of: Tamiya to JST charger adapter
• 1 of: Kill plug style 2
• 1 of: MHS speaker mount V4
• 1 of: 2w bass speaker
• 1 of: SPST Momentary tactile switch
• 1 of: 16mm Anti Vandal Momentary Nickel Plated Switch
• 1 of: MPS Pommel style 10
• 1 of: MPS Clip
• 1 of: MPS Insert style 6
• 1 of: Screw on LED blade holder style 17
• 1 of: MHS choke style 2
• 1 of: Hilt style 3 with standard style switch hole
• 1 of: 8-32 x 1/8" Set Screw
• 1 of: Custom Mill Work Fee
• 1 of: Drill & Tap Hole (8-32)
• 1 of: Custom Mill Work Fee
• 1 of: Recharge port hole service (Style 1)
• 1 of: Machine recessed AV switch hole
• 1 of: Switch 22 mounting hole service
• 1 of: 6 Wire quick connector

• 1 of: PCB for 7.2V Li-ion battery packs

Some of you may immediately notice a couple of critical things are missing - notably a power source, and a way to regulate the current and voltage to the main LED - but I will get onto these in subsequent posts.

The aim of the build was to create a simple, sleek, minimalist design - something that could be swung around with a good feel to it
However, I must admit the copious amount of accent LEDs, while non-canon, were an indulgence.

To estimate how long I wanted the polycarbonate blade to be I used a broom handle, gripping it in my right hand, my arm relaxed in a natural way against my side and the handle pointed downwards. I then adjusted the location where I gripped the handle until its tip was about an inch off the ground. I then used the measured length of handle between my grip and the tip to determine the blade length. The ordered length needed to take into account where on the saber I would have my forward hand, how much distance would be taken up by the choke and blade holder, and how much blade was countersunk into the blade holder. All this mathematics ended up at a value of 30inches.

I'm afraid that I am not a machinist, and nor do I have room in my small apartment to house a milling machine and lathe, as much as it would be great to have these. So there are a number of custom work and drilling fees in this order - all of which were delivered exactly as specified. Thanks again to Tim.

So, that's it for this post - next post, batteries…

Lord Zen
05-26-2013, 01:23 PM
I never intended to build a battery pack


In fact the whole idea scared the hell out of me - soldering a lithium ion cell was an intimidating prospect.

I would have much preferred to order a ready made lithium ion pack (http://www.thecustomsabershop.com/74v-Li-ion-1050mAh-14650-Battery-Pack-P759.aspx), but as I live in the old-world the IATA had other ideas - Loose lithium ion packs cannot be shipped by airfreight now, and with the recent incidents with the Boeing 787 this is understandable.

I liked the idea of using 14650 batteries as they have a small diameter, and placed side-by-side in a hilt still have room above them to seat electronics. Being slightly longer than the 14500s (65mm vs 50mm) they offer a little more run time due to the larger milliamp hours (mAh) rating.

Knowing that Lithium-ion was going to be the only way to provide the voltage and amp hours I wanted I needed to source a set of 14650s, which ended up with me ordering some protected lithium-ions batteries from eBay, imported from China. The old-world apparently doesn't do 14650s

With the batteries on a slow boat from the near other side of the planet, I had plenty of time to read Azmaria Dei's guide to Lithium Ion Battery packs (http://forums.thecustomsabershop.com/showthread.php?12829-Li-Ion-Battery-Packs) - and prepare.
I read this post, re-read it, and then read it some more for good measure.



Now, I would not recommend anyone consider the following advice or guidance - this is simply what I did

When the batteries arrived I knew that they were protected cells and would need to be de-protecting. I intended to connect the cells in series to deliver 7.2V so this would need a 7.2V protection circuit, and using two, competing protection circuits would not be a good idea.

To remove the protection circuit I had to unwrap the cells from their blue plastic wrapping case. You can see the bare-metal cell in the picture below, the protection circuit is on the -ve terminal with a metal connection running along the other end.

http://i1273.photobucket.com/albums/y420/LordZenSaber/Igniter_Lightsaber_01_zpsf6f8af6a.jpg (http://s1273.photobucket.com/user/LordZenSaber/media/Igniter_Lightsaber_01_zpsf6f8af6a.jpg.html)


You might also be able to see the thin piece of yellow cellophane plastic that isolates the metal connection for the cell casement - it is very important the metal case does not touch this metal connection. I carefully cut this long metal tab, lifted the protection circuit from the negative and cut the join to the negative terminal. I then used 14mm heat shrink to re-wrap the individual metal cases and used the metal tabs to solder the cells together along with the 7.2V protection circuit.



With much trepidation I tested my homemade battery pack.
I hooked up the pack to the charger using a JST connector and gingerly turned on the power.
A new battery pack needs to be hooked up to a charger to enable the protection circuit, otherwise the pack remains in a dormant state and no power can be drawn from it.

I was happy that the charger showed red - indicating the pack was at least charging.
I was then really happy when I disconnected the charger and measured 7.2V from the pack.
I then left the pack charing for about 20mins, paranoid that the pack would go bang.

Fortunately there were no fireballs, and the charger LED showed green, indicating the pack was fully charged.

It looked like my homemade lithium ion pack was a success

Lord Zen
05-26-2013, 02:39 PM
This is the LED Engin, and sadly it is not the originally ordered one

http://i1273.photobucket.com/albums/y420/LordZenSaber/IMG_0640_zps7566c462.jpg (http://s1273.photobucket.com/user/LordZenSaber/media/IMG_0640_zps7566c462.jpg.html)

Because I could not decide on which colour I would like my saber blade to be, I elected to use a multi-coloured RGBW LED (http://www.thecustomsabershop.com/LED-Engin-LZ4-10W-Multi-Color-P712.aspx) and originally considered using potentiometers to adjust the current level to adjust the colour.

Fortunately a couple of products were announced at this time that offered RGB colour mixing on the soundcard. My decision was to go with Naigon's Igniter soundcard - I appreciate that this product is not sold in this store, so will not go into details.


The LED Engin had many names during the soldering process - none of them repeatable in this forum...

This LED was the hardest thing to solder on the project by a long way, but thanks to Fender's wiring guide (http://forums.thecustomsabershop.com/showthread.php?13703-LEDengin-5w-and-10W-info-and-wiring-guide-for-noobs) I was at least prepared for this.


I used a 30W soldering iron and the LED star was held in place using a helping-hands grip system. The aluminium base of the star does an incredible job of dissipating heat, so you need to work fast. I also found out that the LED Engin is more tolerant and robust to heat than I initially thought.

http://i1273.photobucket.com/albums/y420/LordZenSaber/Igniter_Lightsaber_03_zps3a0c3e9d.jpg (http://s1273.photobucket.com/user/LordZenSaber/media/Igniter_Lightsaber_03_zps3a0c3e9d.jpg.html)

Once I thought I had finished soldering up this beast, and to my horror, I broke one of the pads on the green die. The copper pad lifted off the star and the small track to the die snapped.
As I had decided to use the LED Engin specifically for its colour mixing I was just a little upset - so I decided to try to recover this set back.

Using a little sanding I filled back the coating on top of the copper track and attempted to solder to it. This worked temporarily - but was too delicate to handle any wire movement. Knowing the piece was useless to me I practically covered the area in solder - but to no avail. I did however learn how robust these things are - all the other dies still work, and so this broken LED has been consigned to my box of spare things. The red and blue still work - and that makes purple :)

So, having learnt my lessons from the first LED and improved my soldering skills, I ordered another. I also moved to solid core for the connections, with the intension of using strand-core beyond the heat sink. I found this made the soldering easier for me.

Below you can see all the pads wired up - all colour coded black to make things a little more trickier:

http://i1273.photobucket.com/albums/y420/LordZenSaber/Igniter_Lightsaber_05_zps141af01f.jpg (http://s1273.photobucket.com/user/LordZenSaber/media/Igniter_Lightsaber_05_zps141af01f.jpg.html)

And with the LED Engin mounted on the heat sink with the star thermal tape pad and the wires threaded through waiting for connection to coloured multi strand wire. I use a screwdriver to push where the star pad overlaps into the heat sink holes:

http://i1273.photobucket.com/albums/y420/LordZenSaber/Igniter_Lightsaber_06_zpsfe5e4535.jpg (http://s1273.photobucket.com/user/LordZenSaber/media/Igniter_Lightsaber_06_zpsfe5e4535.jpg.html)

Finally the LED housed, with its lens and holder, wired up with the 6 wire quick connector and held in place in the customised blade holder 17 (http://www.thecustomsabershop.com/Screw-on-LED-blade-holder-style-17-P417.aspx) by the choke section:


http://i1273.photobucket.com/albums/y420/LordZenSaber/Igniter_Lightsaber_09_zpscf3e584e.jpg (http://s1273.photobucket.com/user/LordZenSaber/media/Igniter_Lightsaber_09_zpscf3e584e.jpg.html)


The blade holder customisation simply has a 6mm wide cut made into it with a 12mm diameter hole at the end. The blade holder screw is underneath, directly opposite the 12mm hole.

Silver Serpent
05-26-2013, 07:41 PM
The LED Engin had many names during the soldering process - none of them repeatable in this forum...


Below you can see all the pads wired up - all colour coded black to make things a little more trickier:


I found these two statements to be quite amusing. The first one I can relate to personally. The second...well, it just boggles my mind :)

Lord Zen
05-27-2013, 03:16 AM
Unfortunately, on the day I visited my local electronics store their approach to solid core wire was much like Henry Ford's - any colour you wanted as long as it was black

Granted it was a stock availability issue at the time, but there was no time for such nonsense - I had a lightsaber to build!

Lord Zen
05-27-2013, 04:12 AM
I lament not asking Tim to do powder coating on the main hilt.


But to be fair, I didn't realise until I received my order how much better it would look accented with matt black. But more wisdom learnt - let the experts do the powder coating..

I did manage to find a local powder coating who would do small jobs. They would normally do bike frames so I hoped they would be willing to coat the saber hilt.

After getting past the perplexed look of the powder coat guy when I showed him the saber hilt, and pointing out the intricacies of the work that was required, he said that they could do the work but the masking work would be labour intensive and expensive. They could do it for a stupid amount of money, or I could go away and do it myself.

So this is when I learnt the time consuming experience of masking.
I purchased some special masking tape, that could handle the baking temperatures of powder coating, and set about my work. As I wanted to have the groves in the hilt black I needed to mask pretty much everything and carefully cut the edge of the tape with a scalpel to reveal only the groves. The various holes within the hilt, including each end of the tube also needed to be blocked with bungs. It was during this process that I suspected powder coating the whole of the hilt black and taking the top layer of paint off using a lathe might have been the easier way. But with no lathe available, this wasn't an option. The whole task took about 4 hours to complete.

I was really proud of my fully masked hilt, with all the groves and details neatly cut in, it seemed a shame that I would soon be removing it all again.

The fully masked hilt was then powder coated, and the guy charged me about £5 to do so.

Next came the arduous task of removing all the masking tape, and as the paint had dried hard it was a painful experience removing the tape with my fingernail, as I didn't want to damage the aluminium finish underneath.
In some places taking the masking tape off also chipped a little of the powder coating at the edges so I needed to touch them up with some matt black enamel paint.

Fortunately I don't have any photos of this whole shameful process

However, below is the powder coated hilt, with attached pommel, choke and blade emitter, all basking in the sun:

http://i1273.photobucket.com/albums/y420/LordZenSaber/Lightsaber_1_zpsc3fdac1f.jpg (http://s1273.photobucket.com/user/LordZenSaber/media/Lightsaber_1_zpsc3fdac1f.jpg.html)

There are no electronics in here yet and I just rested the Anti-Vandal switch in its hole.
Along the top you can see the where the 7, yes seven, accent LEDs will go - I think I admitted that these were a bit of an indulgence :)
Two LEDs will be located separately in the little black spots in the grooves, and the remaining 5 will be spaced equally along the black strip to the right.

Tim did an incredible job on all the drilling and milling work this required - and I think it looks fantastic.

Silver Serpent
05-27-2013, 06:23 AM
I'm loving the custom bladeholder.

I'm glad to hear you're learning a lot. You're definitely doing a few things the hard way. In the future, if you just want to color in the grooves, you could just use spray paint. Durability is less of an issue in recessed areas. You don't even need to mask the hilt, just take a sanding block and remove the upper material and it's done. Now if the color scheme were reversed and you wanted the grooves clean and the main section black, then the PC would be an ideal choice.

Your way is fine, but it's a lot more effort. As I'm sure you've learned :)

I'm looking forward to seeing all those accent LEDs wired up.

Lord Zen
05-31-2013, 02:20 PM
To give the saber some bling I decided that I would use nearly all of the accent LEDs that the Igniter soundcard can provide.

I know none of the movies have flashing LEDs all over the place, but having one or two is useful - just for debugging and reminding you that you've left your lightsaber on.
So of course having seven would be even better.

I used a chain of 3mm (T3), crystal clear LEDs, which would mean that they would be transparent when powered off, and not detract from the saber's simple design.
I carefully bent all the Anode legs of the LEDs to 90 degrees so I could solder them together in a chain.

http://i1273.photobucket.com/albums/y420/LordZenSaber/IMG_0650_zps919083b5.jpg (http://s1273.photobucket.com/user/LordZenSaber/media/IMG_0650_zps919083b5.jpg.html)

I pushed each LED in turn into the holes cut into the hilt to make sure that the spacing between them would be correct. The anodes were soldered together and any overlap was trimmed. After the powdercoating and sanding the holes a little the LEDs are quite a friction fit into the hilt, so I had to be careful not to get any of them stuck.

http://i1273.photobucket.com/albums/y420/LordZenSaber/IMG_0655_zps6dba2c1a.jpg (http://s1273.photobucket.com/user/LordZenSaber/media/IMG_0655_zps6dba2c1a.jpg.html)

Once the chain was completed, I added a little heat shrink to the ends to cover up the solder joins and exposed LED legs. I then wrapped electrical tape around the linked LEDs, again to protect against exposed connections.

What isn't apparent when the LEDs are powered off are their colours. I decided to avoid a chromatic look, and picked a more random ordering.

The Yin
05-31-2013, 03:38 PM
so the accent LEDs are different colors, a mix of colors?
When I picture that in mind mind, it looks awesome!!
Sounds like it'll give it a nice retro Sci-fi look. You know, back when everything had flashing lights and such, oh yeah, like in Star Wars.
Cant wait to see the finished saber.

Lord Zen
06-01-2013, 04:13 AM
so the accent LEDs are different colors, a mix of colors?

Yeap, I arranged them Blue, Green, Orange, Blue, Yellow, Green, White - and this decision took longer than it should. It is surprisingly difficult to do "random"

I was going to have a purple in there, but it just wasn't as bright as the colours. It almost looked like the purple was broken or mis-wired compared to the other LEDs - so I dropped it and replaced it with the white.



back when everything had flashing lights and such, oh yeah, like in Star Wars. :D

Lord Zen
06-01-2013, 04:22 AM
It is said that one of the final tasks a Jedi faces is the construction of their own lightsaber.
After fitting the recharge port I can understand why…


I located the recharge port about 3 inches down the hilt and opted for a thread to be made in the hole so I could simply screw the recharge port in.

I wired up the recharge port as per Erv's helpful photo (http://www.plecterlabs.com/catalog/article_info.php?articles_id=12), applying heat wrap over each connection and then over the whole circumference of the port to hold with wires tight.



It was then I realised that in order to screw the port into the hilt that it would require liberal application of tweezers, contortions, and telekinetic force powers.

Still, after about 20 minutes I finally managed to get the thing screwed in, and hoped I would never have to do that again.


http://i1273.photobucket.com/albums/y420/LordZenSaber/Lightsaber_3_zpsafb7fc1c.jpg (http://s1273.photobucket.com/user/LordZenSaber/media/Lightsaber_3_zpsafb7fc1c.jpg.html)


You can see from the photo the excellent mill work around the recharge port, keeping the same depth and width of the groves as a surround.
You can also see a pair of JST connectors. One set for the homemade battery pack, and the other for connecting to the sound card. One is male and the other female, to make sure that I cannot connect things the wrong way around...

Lord Zen
06-02-2013, 05:00 AM
It is most satisfying having wired everything up, and pushing the main switch for the first time to be greeted with the famous lightsaber ignition sound.

Below you can see all the internals of the saber wired up and powered on, the 2W speaker (http://www.thecustomsabershop.com/2W-Bass-Speaker-P662.aspx) humming and buzzing:

http://i1273.photobucket.com/albums/y420/LordZenSaber/Igniter_Lightsaber_11_zpse4112701.jpg (http://s1273.photobucket.com/user/LordZenSaber/media/Igniter_Lightsaber_11_zpse4112701.jpg.html)

On the left is the speaker, held inside a v4 speaker mount (http://www.thecustomsabershop.com/MHS-speaker-mount-V4-P661.aspx). I had to cut a small notch in the side so the left-most LED will slot into it when assembled into the hilt.

In the far background is the 7.2V 14650 Lithium-ion battery pack, which connects to the recharge-port (out-of-shot) now firmly secured in the hilt.
In front of the battery pack is the main activation switch, a 16mm nickel plated AV switch (http://www.thecustomsabershop.com/16mm-Anti-Vandal-Momentary-Nickel-Plated-Switch-P471.aspx), and next to it the tiny auxiliary tactile switch (http://www.thecustomsabershop.com/SPST-Momentary-tactile-switch-P641.aspx).

I mounted the igniter daughter board underneath the mainboard using a row of header pins, which kept things tidy and compact.

Finally, there is the 6 wire quick connector (http://www.thecustomsabershop.com/6-Wire-quick-connector-P458.aspx) that is used to connect to the LED Engin.

The next photo shows all of the internals lined up next to the hilt:

http://i1273.photobucket.com/albums/y420/LordZenSaber/Lightsaber_5_zpsb868c0ea.jpg (http://s1273.photobucket.com/user/LordZenSaber/media/Lightsaber_5_zpsb868c0ea.jpg.html)


And this photo shows the blade holder, blade and LED Engin illuminated with the correctly configured colour:

http://i1273.photobucket.com/albums/y420/LordZenSaber/Igniter_Lightsaber_17_zps9bdc2622.jpg (http://s1273.photobucket.com/user/LordZenSaber/media/Igniter_Lightsaber_17_zps9bdc2622.jpg.html)


I then proceeded to create 9 different saber "fonts" each with a different sound, main LED and flash colours, and accent LED blinking patterns.

Silver Serpent
06-02-2013, 07:33 AM
Looking good. One nitpick: Is that electrical tape wrapping your battery pack? You might want to find some heatshrink instead. Electrical tape has a tendency to come loose when it gets warm and gunk up the inside of your saber. Check with some online battery suppliers, some of them carry heatshrink for packs that size.

Lord Zen
06-15-2013, 03:33 AM
Thanks Silver Serpent,

But I'm afraid it gets worse than that...

Lord Zen
06-15-2013, 03:38 AM
This is the part where things start to go badly...

Having wired up all the electronics, tested they worked, the battery pack would recharge, and each of the separate font colours and sounds had been configured, it was time to put all of the gubbins into the small metal tube.

The original plan was to seat the sound card and daughter card on top of the battery pack - but this didn't quite work by a frustratingly small amount. So the sound card was positioned so that the daughter card hung over the end of the battery pack.

While sliding the battery pack and sound card into the hilt the pack became caught on the recharge port legs. Pushing a little harder resulted in the pack easily sliding in. A little too easily it turned out - I had snapped the legs off the recharge port.

So, sliding the pack back out again, I was faced with the task of removing the recharge port and replacing it. Fortunately the local electronics store stocked equivalent sockets. This time I pre-cut and bent the connection-tabs so that nothing extended beyond the main body of the socket - making it a little more robust. I then had to re-engage in the activity of contortions and force-mastery to get the new port back in the same location in the hilt.

The next fun activity after seating the battery pack and sound card, which fitted by fluke more than design without obstructing the AV switch, was fitting the accent LEDs in place.

I had foolishly used a totally inappropriate gauge of wire, so the LEDs put up more a a fight about where they wanted to be versus where I wanted them to be. Using a wooden chopstick I manipulated each LED to its dedicated hole, which was made tricker by the fact all the LEDs looked the same. Sadly not all of the LEDs made it alive. The 3rd LED along didn't make it.

I then screwed in the AV switch, backed with a couple of o-rings to have a nice fit against the internal curvature of the hilt. The speaker mount was slid in using the notch cut into it to slide over the far LED.


I then connected the LEDEngin to the sound card using the 6-way quick connector and tested everything still worked. It was after making this join and attempting to screw in the blade holder that I discovered the next horror. The blade holder wouldn't screw all the way in. And that was just annoying.

The cumulative effect of the daughter board not fitting on top of the battery had shifted everything along.

The saber would have been fine if I didn't need to fit the battery pack in it:

http://i1273.photobucket.com/albums/y420/LordZenSaber/IMG_0644_zps4c91e92d.jpg (http://s1273.photobucket.com/user/LordZenSaber/media/IMG_0644_zps4c91e92d.jpg.html)

So this is where the difficult decision came. I decided to take it all apart again…

I cut all the wires to the accent LEDs and set about making a new set - using the thinner black wire as opposed to the really thick white wire.

I cut and replaced the wires to the tactile switch.

I cut the 6-way quick connector cables, to shorten the connection from the LEDEngin.

I took apart my homemade battery pack, desoldered the links and remade it with 14500s.


I then slowly began to put everything back in the hilt again.



The thinner gauge wire and smaller battery pack made installing things far easier - and I now had better experience of how to slide everything in.

The final manipulation was to connect the two ends of the 6-way quick-connector - and to do this 1inch into the hilt and partially obscured by the battery pack. A pair of tweezers, a chopstick and swearing seemed to do the job.


Finally everything is in its place.

Silver Serpent
06-15-2013, 05:25 AM
Welcome to the fine art of Cram-Fu. It's not as easy as it looks, but it does get easier with time. The swearing really does help.

Congrats on getting the saber assembled!

Yoshi-Taka
06-15-2013, 06:23 AM
The swearing really does help.
It really does.. louder volumes and more frequent swearing seems to accelerate the process.

I really like this saber. The simplicity in the hilt design is beautiful, the array of accent LEDs is fantastic, it uses my favourite emitter (the cutout in that looks awesome, btw).. I love this saber.

Forgetful Jedi Knight
06-15-2013, 12:10 PM
Welcome to the fine art of Cram-Fu. It's not as easy as it looks, but it does get easier with time.

Exactly.... trying to cram the world into a saber isn't as easy as it looks, but this is how you learn. Congrats on getting it finished!

Lord Zen
06-16-2013, 08:35 AM
Thank you all for your kind words, it is most appreciated :D

Lord Zen
06-16-2013, 09:38 AM
As my lightsaber has been completed I thought it only fair to share a couple of photos :)
You might also spot one of ARKM's excellent crystal razor blade plugs (http://forums.thecustomsabershop.com/showthread.php?10024-quot-Razor-quot-Blade-plugs&)




http://i1273.photobucket.com/albums/y420/LordZenSaber/th_IMG_1163_zpse136e1ec.jpg (http://s1273.photobucket.com/user/LordZenSaber/media/IMG_1163_zpse136e1ec.jpg.html)

http://i1273.photobucket.com/albums/y420/LordZenSaber/th_IMG_1168_zps912ada0c.jpg (http://s1273.photobucket.com/user/LordZenSaber/media/IMG_1168_zps912ada0c.jpg.html)

http://i1273.photobucket.com/albums/y420/LordZenSaber/th_IMG_1206_zpsa89e7438.jpg (http://s1273.photobucket.com/user/LordZenSaber/media/IMG_1206_zpsa89e7438.jpg.html)

http://i1273.photobucket.com/albums/y420/LordZenSaber/th_IMG_0758_zps5bf97d22.jpg (http://s1273.photobucket.com/user/LordZenSaber/media/IMG_0758_zps5bf97d22.jpg.html)



http://i1273.photobucket.com/albums/y420/LordZenSaber/IMG_1170_zps4029536b.jpg (http://s1273.photobucket.com/user/LordZenSaber/media/IMG_1170_zps4029536b.jpg.html)





And a short video:

http://i1273.photobucket.com/albums/y420/LordZenSaber/th_LordZensLightsaber_zpsf54bbed5.jpg (http://i1273.photobucket.com/albums/y420/LordZenSaber/LordZensLightsaber_zpsf54bbed5.mp4)


Thanks for reading

TrypWyr
06-16-2013, 01:02 PM
Wonderful job, Lord Zen!

I love the overall simplicity of the saber design, it really draws your eye to the grooves and cut-outs. And I LOVE that blade holder! Cutting that notch makes it look completely different, and the hole drilled at the base of the notch gives it that little something extra. Also one of the more entertaining write ups I've read. ;)

Now step away from the forums and go build another saber!

Nemesis
06-18-2013, 09:54 AM
Nice build Lord Zen! Love the led strip and blade holder. Very elegant saber.