Strydur
04-05-2012, 11:32 AM
We are proud to announce that once again the PC has been upgraded.
We now have Version 2.0 in stock and ready to ship. Here are the new specs.
Features & Maximum Ratings
Dimensions: 1.9" x .93" x .3" (with the microSD card).
Power supply: 5.5 to 11 V / 2.5A (with the High-power LED). 2 li-ion cells (18650 or 14500) batteries recommended.
Idle current consumption : 3 mA (deep sleep mode)
2A high-power LED driver
Speaker: 4 to 8 ohm.
Audio output Power : 2W
Accent LEDs: 2
32 stages sequence with stop and loop instructions (using either 0 or 65535 for the delay)
Accent LEDs pad current source: 18 mA max per pad
Handles momentary or latching switch for on/off control
High end motion sensing technology
100% compatibility with CF sound fonts, 8 clash, 8 swings, lockup, force sounds.
Blaster Blocking & Lockup Fx
Blade Flickering Fx
Blade Shimmering on Clash
Anti Power Off technology (A-POP™)
Foc™ Flash on Clash™
WAV file support
12 bit sounds
Hum resume: defines if you come back to where the hum has been interrupted or not. Interesting for certain hums. Not sample accurate but resumes the hum in a ballpark of 11ms from where it's been interrupted by a fx sound.
Anti power off delay (offd) : variant of our Anti Power Off technology (APOP) use an adjustable delay when cycling the the activation switch.
Led current parameter now takes mA. To get 2A you would enter 2000, for 1.5A 1500 etc
Motion sensing thresholds now go up to 1023 (ls, hs, lc)
General sensitivity (i) is now an integer between 0 and 99. Same kind of value than on CFv5. Previously entered as float number (0.65) but is now 65.
Wiring is very similar to current CF, down to the accent LEDs location and FoC pad.
Shorter than PC 1.6
Mute on the go
We now have Version 2.0 in stock and ready to ship. Here are the new specs.
Features & Maximum Ratings
Dimensions: 1.9" x .93" x .3" (with the microSD card).
Power supply: 5.5 to 11 V / 2.5A (with the High-power LED). 2 li-ion cells (18650 or 14500) batteries recommended.
Idle current consumption : 3 mA (deep sleep mode)
2A high-power LED driver
Speaker: 4 to 8 ohm.
Audio output Power : 2W
Accent LEDs: 2
32 stages sequence with stop and loop instructions (using either 0 or 65535 for the delay)
Accent LEDs pad current source: 18 mA max per pad
Handles momentary or latching switch for on/off control
High end motion sensing technology
100% compatibility with CF sound fonts, 8 clash, 8 swings, lockup, force sounds.
Blaster Blocking & Lockup Fx
Blade Flickering Fx
Blade Shimmering on Clash
Anti Power Off technology (A-POP™)
Foc™ Flash on Clash™
WAV file support
12 bit sounds
Hum resume: defines if you come back to where the hum has been interrupted or not. Interesting for certain hums. Not sample accurate but resumes the hum in a ballpark of 11ms from where it's been interrupted by a fx sound.
Anti power off delay (offd) : variant of our Anti Power Off technology (APOP) use an adjustable delay when cycling the the activation switch.
Led current parameter now takes mA. To get 2A you would enter 2000, for 1.5A 1500 etc
Motion sensing thresholds now go up to 1023 (ls, hs, lc)
General sensitivity (i) is now an integer between 0 and 99. Same kind of value than on CFv5. Previously entered as float number (0.65) but is now 65.
Wiring is very similar to current CF, down to the accent LEDs location and FoC pad.
Shorter than PC 1.6
Mute on the go