PDA

View Full Version : Sink Tube over the MHS.



Drewbacca
08-05-2006, 09:37 PM
So I took my MHS with me to Home Depot so I could properly fit some rubber O-rings. Which by the way snazzed it up quite a bit. Anyway...I walked on down to the sink tube area, picked up a 1 1/2" sink tube(which supposedly the mhs fits into) and slid my MHS into it. Well..it scratched it up fairly well. So my question is...how do I shine it up (what sand paper and polish), and how the hell do I get an outer sink tube on without it scratching the holy hell out of my aluminum MHS? I was pretty careful and it still scratched.

Thanks [:D]

________________________________
"That's 'cause droids don't pull people's arms out of their sockets when they lose. Wookiees are known to do that."

Drewbacca
08-05-2006, 09:39 PM
My buddy has a metal etching tool that he's going to let me borrow, so that's why I was testing out the sink tubes. Gonna have on of my friends with a BA to draw me up a nice design to etch into it.

________________________________
"That's 'cause droids don't pull people's arms out of their sockets when they lose. Wookiees are known to do that."

Lord Maul
08-05-2006, 10:45 PM
i think you use 1200 grit sandpaper but i'm not sure

At last we will reveal ourselves to the jedi, at last we will have revenge.

Jedi Ranger
08-06-2006, 04:29 AM
My experience and recommendations for sliding a sink tube over the MHS:

1) Make sure that both parts are totally clean. Send a rag through the sink tube, especially.

2) Make sure that the open end of the sink tube being slid ahs been sanded down. This is usually the biggest problem-causer.

3) Because it is such a perfect fit, there is barely enough room for a couple layers of paint, and a sink tube. Expect some scratches. But go VERY slowly, to try to limit any damage.

4) If need be, slid on the sink tube, and do the sanding, polishing, and any painting AFTER.

I hope some of these tips help. Good luck!

<center>http://www.members.shaw.ca/Jedi.Ranger/images/Jedi_Ranger_Banner_4.1.jpg
http://www.members.shaw.ca/Jedi.Ranger/</center>

Do-Clo
08-06-2006, 08:50 AM
You can use some 1000 grit sandpaper then a good metal polish to restore your mhs, with some good polishing you can make it really shine.

<center>http://i48.photobucket.com/albums/f217/Do-Clo/DoCloSig.jpg</center>
<center><font color="red"><font size="4"><font face="Comic Sans MS">Darth Technous Sith Lord</font id="Comic Sans MS"></font id="size4"></font id="red"></center>
<center><font color="red"><font size="4"><font face="Comic Sans MS">Give yourself to the Dark Side</font id="Comic Sans MS"></font id="size4"></font id="red"></center>

Drewbacca
08-06-2006, 12:54 PM
Thanks fellas.

________________________________
"That's 'cause droids don't pull people's arms out of their sockets when they lose. Wookiees are known to do that."

Jedi-Loreen
08-06-2006, 02:50 PM
<blockquote id="quote"><font size="1" face="Verdana, Arial, Helvetica" id="quote">quote:<hr height="1" noshade id="quote">Originally posted by Jedi Ranger

My experience and recommendations for sliding a sink tube over the MHS:

1) Make sure that both parts are totally clean. Send a rag through the sink tube, especially.

2) Make sure that the open end of the sink tube being slid ahs been sanded down. This is usually the biggest problem-causer.

3) Because it is such a perfect fit, there is barely enough room for a couple layers of paint, and a sink tube. Expect some scratches. But go VERY slowly, to try to limit any damage.

4) If need be, slid on the sink tube, and do the sanding, polishing, and any painting AFTER.
<hr height="1" noshade id="quote"></blockquote id="quote"></font id="quote">


<font color="purple"><font size="3">You can't really do any of that when you are fitting sink tubes at the hardware store though. That's where the trouble begins, with getting scratches on your hilt. If you want to make sure a sink tube will fit before you buy it you're pretty much screwed, the hilt's gonna get scratched.</font id="size3"></font id="purple">


In order to see the Light, you must sometimes risk the Dark.

Jedi Ranger
08-06-2006, 03:49 PM
Ahhh, yes. Very true.

Accept the strong possibility of scratches when test fitting parts.

<center>http://www.members.shaw.ca/Jedi.Ranger/images/Jedi_Ranger_Banner_4.1.jpg
http://www.members.shaw.ca/Jedi.Ranger/</center>

Lord Maul
08-06-2006, 04:48 PM
so just buy a bunch of different pipes, take them home and try them out. then return the ones that don't work

At last we will reveal ourselves to the jedi, at last we will have revenge.

Strydur
08-06-2006, 11:02 PM
You could also buy the sink tubes from me which are far better quality and cost less than the ones at lowes/home depot.

Tim
The Custom Saber Shop

archammer2
08-07-2006, 04:10 PM
Ya know, Drew, thanks for making this thread. When I got my first MHS, I scratched the hell out of it trying to get a sink tube on. I just thought I was an idiot. =P

~~~~~~~~
Support a starving artist:
http://archammer2.deviantart.com